メインコンテンツにスキップ

ProntoTec Axius Screen Replacement

必要な工具と部品

  1. ProntoTec Axius Screen Replacement, Screen: 手順 1、 1の画像 1
    • Make sure the device is completely turned off before you begin taking it apart to avoid risk of electrocution.

    • Place the tablet face-up on a flat table

  2. ProntoTec Axius Screen Replacement: 手順 2、 1の画像 1
    • Starting near the headphone port, fit the flat end of the spudger in between the screen and back case.

    • Pry the back case from the screen around each point on the device to release the clips securing the case halves to each other.

  3. ProntoTec Axius Screen Replacement: 手順 3、 1の画像 1
    • Gently remove the back case of the device and lay it in a flat surface as shown in the photo.

    • Make sure not to sever the wires (red and black) connected to the speaker that is located in the back case.

  4. ProntoTec Axius Screen Replacement: 手順 4、 1の画像 1
    • Remove all of the yellow tape that is on the device with the spudger.

    • Be careful not to cut any wires that are under the tapes.

  5. ProntoTec Axius Screen Replacement: 手順 5、 2の画像 1 ProntoTec Axius Screen Replacement: 手順 5、 2の画像 2
    • Use the flat end of the spudger to gently pry the battery from the back of the screen.

  6. ProntoTec Axius Screen Replacement: 手順 6、 2の画像 1 ProntoTec Axius Screen Replacement: 手順 6、 2の画像 2
    • Use a spudger to lift all the ribbon cable clamps

    • Detach all three ribbon cables from the clamps

  7. ProntoTec Axius Screen Replacement: 手順 7、 3の画像 1 ProntoTec Axius Screen Replacement: 手順 7、 3の画像 2 ProntoTec Axius Screen Replacement: 手順 7、 3の画像 3
    • Using a Phillips screwdriver (PH00), unscrew the motherboard from the device

  8. ProntoTec Axius Screen Replacement: 手順 8、 3の画像 1 ProntoTec Axius Screen Replacement: 手順 8、 3の画像 2 ProntoTec Axius Screen Replacement: 手順 8、 3の画像 3
    この手順で使用する道具:
    Heavy-Duty Spudger
    $4.99
    購入する
    • Use the flat end of the metal spudger to remove the battery from the back of the screen of the device.

    • Avoid using metal when prying off the battery. For serious prying power, try using the heavy-duty plastic spudger.

  9. ProntoTec Axius Screen Replacement: 手順 9、 1の画像 1
    • Remove the orange tab from the back of the screen as shown in the picture

  10. ProntoTec Axius Screen Replacement: 手順 10、 2の画像 1 ProntoTec Axius Screen Replacement: 手順 10、 2の画像 2
    • Use the flat end of the metal spudger to unclip and remove the screen from the casing.

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

5人の作成者と共同で作成されました。

Antonio Irons

メンバー登録日: 10/20/16

441 ポイント

4のガイドは作成済み

チーム

UMass Dartmouth, Team 5-3, Martin Fall 2016 UMass Dartmouth, Team 5-3, Martin Fall 2016人のメンバー

UMASSD-MARTIN-F16S5G3

3 メンバー

10のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 1

過去 7 日: 4

過去 30 日: 5

今までの合計 274