はじめに

How to remove the PCMCIA card cage holder.

Remove the battery.
  • Remove the battery.

  • Turn the keyboard locking screw so that it is parallel to the space bar.

  • Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.

コメントを追加する

Rest the keyboard face down on the trackpad area.
  • Rest the keyboard face down on the trackpad area.

  • Disconnect the keyboard connector from the logic board.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.
  • Release the tabs on each side of the RAM chip at the same time. These tabs lock the chip in place and releasing them will cause the chip to "pop" up.

  • Pull the RAM chip out.

  • Repeat this process if a second RAM chip is installed.

コメントを追加する

  • Turn the G4 over.

  • Remove the eight Phillips screws from the lower case.

コメントを追加する

Using your thumbs, slide the lower case away from you.
  • Using your thumbs, slide the lower case away from you.

  • The lower case may stick in the front on a tab just above the center of the DVD drive. Be careful as you work the case off, or you may break the thin strip of plastic just above the drive.

  • Lift the lower case off.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Skip this step if your computer does not have an Airport card.
  • Skip this step if your computer does not have an Airport card.

  • Firmly grasp the plastic tab attached to the Airport card and pull up and to the left.

  • Disconnect the antenna cable from the left side of the Airport card.

コメントを追加する

Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.
  • Disconnect the hard drive ribbon from the logic board using a spudger or the tip of your finger.

コメントを追加する

To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.
  • To free the hard drive, remove the two T8 Torx screws from the right wall of the battery housing.

コメントを追加する

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Remove the hard drive by gently grasping the orange ribbon cable and lifting the left edge up and out of the computer.
  • Remove the hard drive by gently grasping the orange ribbon cable and lifting the left edge up and out of the computer.

  • There are four rubber bumpers that fit over the hard drive screws. Ensure that these bumpers come out when you remove the hard drive.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Before continuing, place a soft cloth on your work surface to rest the computer on. Turn the G4 over, making sure the DVD drive doesn't fall out.
  • Before continuing, place a soft cloth on your work surface to rest the computer on. Turn the G4 over, making sure the DVD drive doesn't fall out.

  • Carefully peel the adhesive strip away from the DVD drive. The plastic dust shield covering the DVD drive is easily damaged. Try to start at the four corners and work toward the center.

コメントを追加する

Bend the silver metal EMI clip so that it is vertical. This part may fall out after removing the DVD drive.
  • Bend the silver metal EMI clip so that it is vertical. This part may fall out after removing the DVD drive.

  • The EMI clip is not essential for reassembling the computer. If the clip falls out, don't worry about putting it back in.

コメントを追加する

Turn the G4 over.
  • Turn the G4 over.

  • Disconnect both orange ribbon cables from the logic board using a spudger or the tip of your finger.

コメントを追加する

Remove the DVD drive by lifting the right edge up and out of the computer.
  • Remove the DVD drive by lifting the right edge up and out of the computer.

  • If you have a CD or any other object jammed in your optical drive, we have an optical drive repair guide.

コメントを追加する

Turn the G4 over.
  • Turn the G4 over.

  • Using a 5 mm nut driver or needle-nose pliers, remove the hex nut from the modem.

コメントを追加する

Lift the modem out by pulling up and to the right.
  • Lift the modem out by pulling up and to the right.

  • The plastic shielding on the modem may catch on the computer's case. Rocking the modem from side to side will help free the modem.

コメントを追加する

Disconnect the connector cable from the modem.
  • Disconnect the connector cable from the modem.

コメントを追加する

Turn the G4 over.
  • Turn the G4 over.

  • Peel the orange tape away from the three connectors on the PMU board. Leave this tape in place so you can reuse it when reassembling the G4.

  • Disconnect the two orange cables and one multicolored cable from the PMU.

コメントを追加する

Lift up on the silver metal clip to free the PMU from the casing.
  • Lift up on the silver metal clip to free the PMU from the casing.

  • Remove the PMU rotating it clockwise and pulling up.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Turn the G4 over and rest it on a soft cloth.
  • Turn the G4 over and rest it on a soft cloth.

  • Disconnect the multicolored fan connector and battery connector from the logic board.

  • Disconnect the orange PC card cage connector from the logic board.

コメントを追加する

Remove the single T8 Torx screw located next to the PC Card cage.
  • Remove the single T8 Torx screw located next to the PC Card cage.

コメントを追加する

Turn the G4 over.
  • Turn the G4 over.

  • Remove the two T8 Torx screws from the middle of the logic board.

コメントを追加する

Disconnect the four indicated connectors from the logic board, removing tape as necessary.
  • Disconnect the four indicated connectors from the logic board, removing tape as necessary.

コメントを追加する

Carefully lift the logic board up and pull it away from you. The logic board may catch on the back panel ports liner. If this occurs, use a spudger or non-metal tool to free the logic board.
  • Carefully lift the logic board up and pull it away from you. The logic board may catch on the back panel ports liner. If this occurs, use a spudger or non-metal tool to free the logic board.

  • This step requires some force, but if the logic board will not come up, make sure you have removed all screws and connectors necessary.

  • Remove the logic board from the computer.

コメントを追加する

Your laptop should look approximately like this.
  • Your laptop should look approximately like this.

コメントを追加する

Remove the two T8 Torx screws that secure the PC Card cage.
  • Remove the two T8 Torx screws that secure the PC Card cage.

Left screw is 4.5mm, right screw is 6.5mm.

Teovall - 返信

Remove the PC Card cage by pulling it to the right and twisting slightly toward you.
  • Remove the PC Card cage by pulling it to the right and twisting slightly toward you.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

添付文書

iRobot

メンバー登録日: 2009年09月24日

1 ポイント

750のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 6

今までの合計 4,977