メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

パーツ

パーツは指定されていません。

  1. この手順は未翻訳です。 翻訳を手伝う。

    The Power Mac G4 MDD: the last, and the fastest G4-based Mac.  This computer boasted up to a Dual 1.42GHz PowerPC G4 CPU (though I have a single 1.25GHz). Two USB 1.1 Ports
    • The Power Mac G4 MDD: the last, and the fastest G4-based Mac. This computer boasted up to a Dual 1.42GHz PowerPC G4 CPU (though I have a single 1.25GHz).

    • Two USB 1.1 Ports

    • Assorted Audio

    • Video (ADC & DVI)

    • Networking (RJ-45 Ethernet/56k Modem)

    • Some later model MDD's (such as the dual 1.42GHz) Have a FireWire 800 Port Here:

  2. この手順は未翻訳です。 翻訳を手伝う。

    Unplug the computer. Unplug the power supply and all external connections from the computer. Pull on the side lever and lower the side of the case.
    • Unplug the computer.

    • Unplug the power supply and all external connections from the computer.

    • Pull on the side lever and lower the side of the case.

  3. この手順は未翻訳です。 翻訳を手伝う。

    The hard drive cages are located here.
    • The hard drive cages are located here.

  4. この手順は未翻訳です。 翻訳を手伝う。

    Cage 1 Start by removing this screw. Remove the ATA-66/ IDE ribbon cable from the motherboard.
    • Cage 1

    • Start by removing this screw.

    • Remove the ATA-66/ IDE ribbon cable from the motherboard.

  5. この手順は未翻訳です。 翻訳を手伝う。

    Now, remove the power connection from the drives. Now, remove the power connection from the drives.
    • Now, remove the power connection from the drives.

  6. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  7. この手順は未翻訳です。 翻訳を手伝う。

    Push this tab down, and pull the cage toward you. Now, you can set cage 1 aside. Now, you can set cage 1 aside.
    • Push this tab down, and pull the cage toward you.

    • Now, you can set cage 1 aside.

  8. この手順は未翻訳です。 翻訳を手伝う。

    Cage 2: Remove this Phillips screw:
    • Cage 2:

    • Remove this Phillips screw:

    • Disconnect this IDE ribbon cable from the logic board.

  9. この手順は未翻訳です。 翻訳を手伝う。

    It's likely that there is a cable clip holding the ribbon cable to the case. To remove it, push the end, and it should pop up.
    • It's likely that there is a cable clip holding the ribbon cable to the case.

    • To remove it, push the end, and it should pop up.

  10. この手順は未翻訳です。 翻訳を手伝う。

    With the ribbon cable clip free, pull this tab towards you, slide the cage up until it hits the platform under the power supply, and pull it away. Now, set the cage on top of the CPU, and remove the power connectors. Now, set the cage on top of the CPU, and remove the power connectors.
    • With the ribbon cable clip free, pull this tab towards you, slide the cage up until it hits the platform under the power supply, and pull it away.

    • Now, set the cage on top of the CPU, and remove the power connectors.

  11. この手順は未翻訳です。 翻訳を手伝う。

    Once the cables are free, set the drive cage aside. To remove the hard drives from the cages, remove the four screws on the sides of the cage that are connected to the drives, then slide the drives out.
    • Once the cables are free, set the drive cage aside.

    • To remove the hard drives from the cages, remove the four screws on the sides of the cage that are connected to the drives, then slide the drives out.

    • The two cages are cross compatible and can be put in either location.

    • The MDD does not have a 128GB drive limit like older Macs. My MDD has 3 drives (a 400GB Hitatchi Deskstar, 40GB Seagate Barracuda 7200.7, and a 30GB Quantum Fireball LCT).

    • Note the ID jumpers on the two drive set. One is set to Master, the other to slave. A single drive can be set to Cable Select.

  12. この手順は未翻訳です。 翻訳を手伝う。

    Start removing the optical drive cage by removing its back cover. Start removing the optical drive cage by removing its back cover.
    • Start removing the optical drive cage by removing its back cover.

  13. この手順は未翻訳です。 翻訳を手伝う。

    Now, remove the IDE and power cables from the drives. Now, remove the IDE and power cables from the drives. Now, remove the IDE and power cables from the drives.
    • Now, remove the IDE and power cables from the drives.

  14. この手順は未翻訳です。 翻訳を手伝う。

    Remove these two Phillips screws: Pull the cage away from the front until it is free. Slide the cage towards you, and out of the Mac.
    • Remove these two Phillips screws:

    • Pull the cage away from the front until it is free.

    • Slide the cage towards you, and out of the Mac.

  15. この手順は未翻訳です。 翻訳を手伝う。

    To remove the drive(s) from the cage, remove the two screws on each side of the drive(s), then pull the drive out of the cage. My MDD has a 3rd party 22X SuperDrive, for burning DVD's in Leopard (Thank You Generic Drive Support!)
    • To remove the drive(s) from the cage, remove the two screws on each side of the drive(s), then pull the drive out of the cage.

    • My MDD has a 3rd party 22X SuperDrive, for burning DVD's in Leopard (Thank You Generic Drive Support!)

ゴール

16 の人々がこのガイドを完成させました。

Chris Green

メンバー登録日: 2009年10月11日

34,262 ポイント

45のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

294 メンバー

942のガイドは作成済み

コメント1件

In the Sacramento FATP factory we used to call this the 'media can' in previous models because there were other drives such as ZIP and JAZZ drives available, until this and the one just prior which only had optical drive options, so it became the 'optical cage'

joey - 返信

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 14

今までの合計 11,376