はじめに

The Power Mac G4 MDD had various heatsinks based of the processor, it had a pure copper heatsink for the dual 1.42Ghz model, and a thick finned heatsink for earlier models, and the later models had a thin aluminum finned heatsink.

パーツ

パーツは必要ありません。

The Power Mac G4 MDD: the last, and the fastest G4-based Mac.  This computer boasted up to a Dual 1.42GHz PowerPC G4 CPU (though I have a single 1.25GHz). Six USB ports.
  • The Power Mac G4 MDD: the last, and the fastest G4-based Mac. This computer boasted up to a Dual 1.42GHz PowerPC G4 CPU (though I have a single 1.25GHz).

  • Six USB ports.

  • Four FireWire ports.

  • Assorted SCSI (SCSI50/SCSI68)

  • Assorted Audio

  • Video (ADC & DVI)

  • Networking (RJ-45 Ethernet/56k Modem)

  • Some later model MDD's (such as the dual 1.42GHz) Have a FireWire 800 Port Here:

コメントを追加する

Pull on the side lever and lower the side of the case. Pull on the side lever and lower the side of the case. Pull on the side lever and lower the side of the case.
  • Pull on the side lever and lower the side of the case.

コメントを追加する

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
The ram is between the graphics card, and the CPU, and removal is simple. Push the tabs down on both sides, this will free the ram, then lift it out. The MDD Uses A Maximum of 2GB PC2700 DDR,(512MB X4) and had 4 slots for ram. The MDD Uses A Maximum of 2GB PC2700 DDR,(512MB X4) and had 4 slots for ram.
  • The ram is between the graphics card, and the CPU, and removal is simple. Push the tabs down on both sides, this will free the ram, then lift it out.

  • The MDD Uses A Maximum of 2GB PC2700 DDR,(512MB X4) and had 4 slots for ram.

コメントを追加する

Now, remove these three Phillips screws:
  • Now, remove these three Phillips screws:

  • As there are two Phillips screws well, there are two that you can see in the photo, but you want to remove the screws that are behind them.

コメントを追加する

Now, lift the heatsink up off the computer, it is pretty heavy, because it's a giant block of aluminum. Be careful when holding it, the edges can be sharp, making it likely to get cut if you hold it wrong!
  • Now, lift the heatsink up off the computer, it is pretty heavy, because it's a giant block of aluminum.

  • Be careful when holding it, the edges can be sharp, making it likely to get cut if you hold it wrong!

  • As you may be able to tell, i have applied a replacement coat of Arctic Silver 5 to keep my MDD cooler than the stock paste, it really does a great job too!

コメントを追加する

The incredibly large heatsink, this thing is 5 Lbs of solid aluminum. Just like every other part in this, and many other Macs, the heatsink is made by:                                ...you guessed it, Foxconn. The incredibly large heatsink, this thing is 5 Lbs of solid aluminum. Just like every other part in this, and many other Macs, the heatsink is made by:                                ...you guessed it, Foxconn.
  • The incredibly large heatsink, this thing is 5 Lbs of solid aluminum. Just like every other part in this, and many other Macs, the heatsink is made by: ...you guessed it, Foxconn.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

7 の人々がこのガイドを完成させました。

Chris Green

メンバー登録日: 2009年10月11日

31,857 ポイント

46のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

276 メンバー

718のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 11

過去 30 日: 45

今までの合計 16,711