はじめに

This guide takes you through the process of installing the rear camera on the PlayStation Vita.

Power off and remove the memory card.
  • Power off and remove the memory card.

  • Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.

コメントを追加する

Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.
  • Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.

  • Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.

コメントを追加する

  • Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.

コメントを追加する

  • Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases.

  • Continue working your way around the device gently prying it open.

  • There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.

コメントを追加する

  • Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.

コメントを追加する

  • Using a spudger, free the touch screen controller flex cable by gently prying up the connection.

コメントを追加する

  • Free the battery cable by gently prying up on the connection with a spudger.

Any idea what type of pcb header is on the board for the battery? I have a motherboard with a broken header but I cant source a replacement

Jimbo Jones - 返信

This is where I screwed up so I recommend extra caution for other newbies. Only the black part is supposed to come off. Don't be an idiot like me and pry off too much...

ylimakiminna - 返信

Yea I messed up there too. Is there a way to fix it?

Alethia Henry - 返信

  • Separate the front and rear cases.

コメントを追加する

  • Using the pointy end of the spudger, disconnect the three antenna cable connectors on top of the wireless card.

  • Deroute the antenna cables so that they are out of the wireless card casing. Rest the wires out of the way.

Step 9-11 only apply to the 3G version of the PS Vita.

logicj83 - 返信

Hello, I have the PCH-2001 model of the PS vita and the right analog stick went out. I ordered a replacement and the stick is slightly larger than the original. The original has a black rectangle on the back, the new version has the star version, which is what you have on this website as the replacement part. Any help here would be much appreciated. Thanks.

Ben Ragains - 返信

  • Hook the spudger beneath the tab on the wireless card casing and release the tab.

  • Peel up and remove the wireless card casing.

コメントを追加する

  • Remove the two 4.4mm Phillips #00 screws on the wireless card.

  • The wireless card will naturally pop out at an angle.

  • Pull out the wireless card.

コメントを追加する

  • Pry up the right shoulder button casing with a spudger and set it aside.

コメントを追加する

  • Remove the translucent, plastic right shoulder button cover.

コメントを追加する

  • Release the right shoulder button flex cable socket by using a spudger to gently pry open the tab.

  • Using tweezers, slide the flex cable out of the socket.

コメントを追加する

  • Using a spudger, gently peel up the right shoulder button from the light adhesive connecting it to casing.

コメントを追加する

  • Using the pointy end of a spudger, detach the antenna cable on the right button board.

  • Remove the antenna cable.

コメントを追加する

  • Using a spudger, pry up and release the ZIF socket on the right button board.

  • Gently pull the flex cable out of the socket. Rest the flex cable out of the way.

コメントを追加する

  • Release the tab on the small flex cable socket by prying up the tab with a spudger.

  • Using tweezers, gently pull the flex cable out of the socket. Rest the flex cable out of the way.

コメントを追加する

  • Remove the two 5.0mm Phillips #00 screws from the metal bracket securing the right button board to the motherboard.

  • Remove the metal bracket, using a spudger as necessary to lift it out.

コメントを追加する

  • Use a spudger to free the right button board by prying up from the bottom right corner of board.

  • Gently lift the right button board out.

コメントを追加する

  • Pry up the left shoulder button casing with a spudger.

  • Remove the left shoulder button casing.

コメントを追加する

  • Remove the translucent, plastic left shoulder button cover.

コメントを追加する

  • Release the left shoulder button flex cable socket by using a spudger to pry open the tab.

    • Be careful to not break off this small black tab!

  • Using tweezers, slide the flex cable out of the socket. Do not pull on the black tab! Instead, pull the thin flex cable away from the connector (to the left in this image).

コメントを追加する

  • Using a spudger, gently peel up the left shoulder button from the light adhesive connecting it to casing.

This step is unneccesary.

Alexander Mayatsky - 返信

  • Using a spudger, lift and release the tab on the ZIF socket sitting on the SIM card reader.

  • Carefully pull the flex cable out of the ZIF socket, and rest it out of the way.

コメントを追加する

  • Use a spudger to release the tab between the SIM card reader and the back casing assembly.

  • Lift the SIM card reader off the back casing assembly.

This board is not present in the Wifi only version, only the 3G/Wifi version.

dodo - 返信

  • Release the plastic tab on the small flex cable socket by prying it up with a spudger.

  • Using tweezers, gently remove the small flex cable from the socket, and rest it out of the way.

コメントを追加する

  • Use a spudger to lift up the tab on the large ZIF socket.

  • Gently pull the flex cable out of the ZIF socket, and rest it out of the way.

コメントを追加する

  • Disconnect the white Wi-Fi antenna cable with a spudger.

  • Remove the Wi-Fi antenna cable.

This connector isn't present in the Wifi only version, just the 3G/Wifi version.

dodo - 返信

  • Using a Phillips #00 screwdriver, remove the six screws on the two metal brackets:

    • Two 5.0mm, blue screws on the L-bracket securing the upper left button board to the motherboard.

    • Four 5.0mm, blue screws on the square bracket securing the lower left button board to the motherboard.

What is the loose looking cable in this photo?

Dallon Verhaeghe - 返信

  • Starting from the upper left corner, use a spudger to pry up and remove the left button board.

コメントを追加する

  • Using the pointy end of a spudger, pry up and release the GPS antenna cable from the motherboard.

  • Remove the GPS antenna cable.

コメントを追加する

  • Release the camera flex cable socket by prying up on the tab with a spudger.

コメントを追加する

  • Using a spudger, gently pry up on the camera.

  • Work your way under the camera and along the camera flex cable, using the spudger to peel away the adhesive, freeing the camera.

コメントを追加する

  • Carefully lift and remove the camera, sliding the flex cable out of the open connector socket.

コメントを追加する

  • Using a Phillips #00 screwdriver, remove the 6.3mm screw beneath the camera.

  • Lift and remove the metal camera bracket.

コメントを追加する

  • With the help of a spudger, lift and release the tab on the blue flex cable socket.

コメントを追加する

  • Using tweezers, gently pull the blue power flex cable out of the socket, and rest it out of the way.

コメントを追加する

  • Using a Phillips #00 screwdriver, remove the two pink, 4.4mm screws securing the motherboard.

コメントを追加する

  • Gently peel the rubber tab of the game port cover off the plastic casing pins.

  • Remove the game port cover.

コメントを追加する

  • Gently peel the rubber tab of the accessory port cover off the plastic casing pins.

  • Remove the accessory port cover.

コメントを追加する

  • Starting at the upper right hand corner, use a spudger to gently lift the motherboard out of the casing assembly.

  • The motherboard is still attached to the casing by a connector on the back of the motherboard. Do not pull the motherboard all the way out, or you may damage the connector.

コメントを追加する

  • Lift the motherboard out and identify the OLED connector still attaching the motherboard to the casing.

  • Holding the Vita on its side, use a spudger to gently pry off the OLED connector from the motherboard.

  • Be sure to hold the motherboard while you release the connector as this will free the motherboard. If you are not holding the motherboard, it will fall.

コメントを追加する

  • Completely separate the motherboard from the case. Set the case aside.

コメントを追加する

  • Flip the motherboard over so that the rear camera is facing you on the right.

  • Release the rear camera flex cable socket by prying up on the tab with a spudger. Leave the socket open.

コメントを追加する

  • Gently pull the rear camera out of the flex cable socket.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

Brittany McCrigler

メンバー登録日: 2012年03月05日

79,193 ポイント

134のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

107 メンバー

6,518のガイドは作成済み

コメント1件

This is not it's rear-facing camera though - it is it's front-facing camera.

iFixOmaha LLC - 返信

コメントを追加する

統計データを表示:

過去 24時間: 4

過去 7 日: 6

過去 30 日: 44

今までの合計 3,856