はじめに

This guide takes you through the process of installing the left joystick on the PlayStation Vita.

  1. Power off and remove the memory card.
    • Power off and remove the memory card.

    • Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.

    コメントを追加する

  2. Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.
    • Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.

    • Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.

    コメントを追加する

    • Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.

    コメントを追加する

    • Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases.

    • Continue working your way around the device gently prying it open.

    • There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.

    コメントを追加する

    • Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.

    コメントを追加する

    • Using a spudger, free the touch screen controller flex cable by gently prying up the connection.

    コメントを追加する

    • Free the battery cable by gently prying up on the connection with a spudger.

    Any idea what type of pcb header is on the board for the battery? I have a motherboard with a broken header but I cant source a replacement

    Jimbo Jones - 返信

    This is where I screwed up so I recommend extra caution for other newbies. Only the black part is supposed to come off. Don't be an idiot like me and pry off too much...

    ylimakiminna - 返信

    Yea I messed up there too. Is there a way to fix it?

    Alethia Henry - 返信

  3. 20ドル以上のお買い上げで送料無料(米国内にお住まいの方対象)
    お支払い手続きの際にはクーポンコードBLUEANDBLACKを入力してください。(米国内にお住まいの方対象)
    20ドル以上のお買い上げで送料無料(米国内にお住まいの方対象)
    クーポンコードBLUEANDBLACKをご使用ください。(米国内にお住まいの方対象)
    • Separate the front and rear cases.

    コメントを追加する

    • Pry up the left shoulder button casing with a spudger.

    • Remove the left shoulder button casing.

    コメントを追加する

    • Remove the translucent, plastic left shoulder button cover.

    コメントを追加する

    • Release the left shoulder button flex cable socket by using a spudger to pry open the tab.

      • Be careful to not break off this small black tab!

    • Using tweezers, slide the flex cable out of the socket. Do not pull on the black tab! Instead, pull the thin flex cable away from the connector (to the left in this image).

    コメントを追加する

    • Using a spudger, gently peel up the left shoulder button from the light adhesive connecting it to casing.

    This step is unneccesary.

    Alexander Mayatsky - 返信

    • Using a spudger, lift and release the tab on the ZIF socket sitting on the SIM card reader.

    • Carefully pull the flex cable out of the ZIF socket, and rest it out of the way.

    コメントを追加する

    • Use a spudger to release the tab between the SIM card reader and the back casing assembly.

    • Lift the SIM card reader off the back casing assembly.

    This board is not present in the Wifi only version, only the 3G/Wifi version.

    dodo - 返信

    • Release the plastic tab on the small flex cable socket by prying it up with a spudger.

    • Using tweezers, gently remove the small flex cable from the socket, and rest it out of the way.

    コメントを追加する

    • Use a spudger to lift up the tab on the large ZIF socket.

    • Gently pull the flex cable out of the ZIF socket, and rest it out of the way.

    コメントを追加する

    • Disconnect the white Wi-Fi antenna cable with a spudger.

    • Remove the Wi-Fi antenna cable.

    This connector isn't present in the Wifi only version, just the 3G/Wifi version.

    dodo - 返信

    • Using a Phillips #00 screwdriver, remove the six screws on the two metal brackets:

      • Two 5.0mm, blue screws on the L-bracket securing the upper left button board to the motherboard.

      • Four 5.0mm, blue screws on the square bracket securing the lower left button board to the motherboard.

    What is the loose looking cable in this photo?

    Dallon Verhaeghe - 返信

    • Starting from the upper left corner, use a spudger to pry up and remove the left button board.

    コメントを追加する

    • Using a Phillips #00 screwdriver, remove the two blue, 5.0mm screws attaching the left joystick to the back case.

    コメントを追加する

    • Using a spudger, pry up and remove the left joystick.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

37 の人々がこのガイドを完成させました。

Brittany McCrigler

メンバー登録日: 2012年03月05日

79,908 ポイント

133のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

114 メンバー

7,038のガイドは作成済み

Is it possible to purchase new ps vita analog sticks to replace beaten up ones with?

kay - 返信

Yes. I found them on dealextreme.com, but then saw that shipping could take awhile and double the price. I found a better deal on eBay-- $22 including shipping for a new analog stick.

dodo - 返信

I Live in Kendall,Miami,Does anyone could tell me if there is a place where can I fix my PSVita (The left stick dosent work) Thanks

jamalonso94 - 返信

I have followed these instructions

I have succeeded to replace the joystick but the psvita dont want to turn on and refuse to charge

before the fix the battery was charged to 80%

I have checked all the cables and everything is good

When I push on the power button, the PS light go to orange and stop when I relax the power button

Could you help me please?

mbouchet42 - 返信

Turn on the system let it charge then put it back to sleep

travishenry318 - 返信

is there anywhere i can go to pay someone to do this for me?

Nathan Baker - 返信

is there any safer way

tonya.morse35 - 返信

can i do most of these without a spudge?

karlo.maico - 返信

コメントを追加する

統計データを表示:

過去 24時間: 20

過去 7 日: 114

過去 30 日: 543

今までの合計 48,415