はじめに

This guide takes you through installing the directional pad (D-Pad) on the PlayStation Vita.

Power off and remove the memory card. Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.
  • Power off and remove the memory card.

  • Using a Phillips #00 screwdriver, remove the four 6.4mm screws on the back casing.

コメントを追加する

Using your fingernail or a spudger, pry open the accessory port cover on the top of the device. Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover. Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.
  • Using your fingernail or a spudger, pry open the accessory port cover on the top of the device.

  • Using a Phillips #00 screwdriver, remove the two 5.4mm screws hidden beneath the accessory port cover.

コメントを追加する

Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port. Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.
  • Remove the two 5.4mm Phillips #00 screws on the bottom of the device near the charging port.

コメントを追加する

Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases. Continue working your way around the device gently prying it open. There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.
  • Beginning at the sides of the device, use a plastic opening tool to separate the front and rear cases.

  • Continue working your way around the device gently prying it open.

  • There are still wires holding the front and rear cases together. You may damage the connections if you yank the cases completely apart.

コメントを追加する

Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together. Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.
  • Gently separate the two cases, minding the battery and the touch screen controller connectors holding the two cases together.

コメントを追加する

Using a spudger, free the touch screen controller flex cable by gently prying up the connection.
  • Using a spudger, free the touch screen controller flex cable by gently prying up the connection.

コメントを追加する

Free the battery cable by gently prying up on the connection with a spudger.
  • Free the battery cable by gently prying up on the connection with a spudger.

Any idea what type of pcb header is on the board for the battery? I have a motherboard with a broken header but I cant source a replacement

Jimbo Jones - 返信

This is where I screwed up so I recommend extra caution for other newbies. Only the black part is supposed to come off. Don't be an idiot like me and pry off too much...

ylimakiminna - 返信

Yea I messed up there too. Is there a way to fix it?

Alethia Henry - 返信

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Separate the front and rear cases.
  • Separate the front and rear cases.

コメントを追加する

Pry up the left shoulder button casing with a spudger. Remove the left shoulder button casing. Remove the left shoulder button casing.
  • Pry up the left shoulder button casing with a spudger.

  • Remove the left shoulder button casing.

コメントを追加する

Remove the translucent, plastic left shoulder button cover. Remove the translucent, plastic left shoulder button cover.
  • Remove the translucent, plastic left shoulder button cover.

コメントを追加する

Release the left shoulder button flex cable socket by using a spudger to pry open the tab. Be careful to not break off this small black tab! Using tweezers, slide the flex cable out of the socket. Do not pull on the black tab! Instead, pull the thin flex cable away from the connector (to the left in this image).
  • Release the left shoulder button flex cable socket by using a spudger to pry open the tab.

    • Be careful to not break off this small black tab!

  • Using tweezers, slide the flex cable out of the socket. Do not pull on the black tab! Instead, pull the thin flex cable away from the connector (to the left in this image).

コメントを追加する

Using a spudger, gently peel up the left shoulder button from the light adhesive connecting it to casing. Using a spudger, gently peel up the left shoulder button from the light adhesive connecting it to casing.
  • Using a spudger, gently peel up the left shoulder button from the light adhesive connecting it to casing.

This step is unneccesary.

Alexander Mayatsky - 返信

Using a spudger, lift and release the tab on the ZIF socket sitting on the SIM card reader. Carefully pull the flex cable out of the ZIF socket, and rest it out of the way.
  • Using a spudger, lift and release the tab on the ZIF socket sitting on the SIM card reader.

  • Carefully pull the flex cable out of the ZIF socket, and rest it out of the way.

コメントを追加する

Use a spudger to release the tab between the SIM card reader and the back casing assembly. Lift the SIM card reader off the back casing assembly. Lift the SIM card reader off the back casing assembly.
  • Use a spudger to release the tab between the SIM card reader and the back casing assembly.

  • Lift the SIM card reader off the back casing assembly.

This board is not present in the Wifi only version, only the 3G/Wifi version.

dodo - 返信

Release the plastic tab on the small flex cable socket by prying it up with a spudger. Using tweezers, gently remove the small flex cable from the socket, and rest it out of the way.
  • Release the plastic tab on the small flex cable socket by prying it up with a spudger.

  • Using tweezers, gently remove the small flex cable from the socket, and rest it out of the way.

コメントを追加する

Use a spudger to lift up the tab on the large ZIF socket. Gently pull the flex cable out of the ZIF socket, and rest it out of the way.
  • Use a spudger to lift up the tab on the large ZIF socket.

  • Gently pull the flex cable out of the ZIF socket, and rest it out of the way.

コメントを追加する

Disconnect the white Wi-Fi antenna cable with a spudger. Remove the Wi-Fi antenna cable.
  • Disconnect the white Wi-Fi antenna cable with a spudger.

  • Remove the Wi-Fi antenna cable.

This connector isn't present in the Wifi only version, just the 3G/Wifi version.

dodo - 返信

Using a Phillips #00 screwdriver, remove the six screws on the two metal brackets: Two 5.0mm, blue screws on the L-bracket securing the upper left button board to the motherboard. Four 5.0mm, blue screws on the square bracket securing the lower left button board to the motherboard.
  • Using a Phillips #00 screwdriver, remove the six screws on the two metal brackets:

    • Two 5.0mm, blue screws on the L-bracket securing the upper left button board to the motherboard.

    • Four 5.0mm, blue screws on the square bracket securing the lower left button board to the motherboard.

What is the loose looking cable in this photo?

Dallon Verhaeghe - 返信

Starting from the upper left corner, use a spudger to pry up and remove the left button board. Starting from the upper left corner, use a spudger to pry up and remove the left button board. Starting from the upper left corner, use a spudger to pry up and remove the left button board.
  • Starting from the upper left corner, use a spudger to pry up and remove the left button board.

コメントを追加する

Using tweezers, peel up and remove the directional pad. Using tweezers, peel up and remove the directional pad. Using tweezers, peel up and remove the directional pad.
  • Using tweezers, peel up and remove the directional pad.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

6 の人々がこのガイドを完成させました。

Brittany McCrigler

メンバー登録日: 2012年03月05日

78,374 ポイント

432のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

114 メンバー

5,916のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 18

過去 30 日: 140

今までの合計 8,831