はじめに

How to disassemble and change the Laser Unit.

ビデオの概要

Turn off the console and disconnect all cables.
  • Turn off the console and disconnect all cables.

コメントを追加する

You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws.
  • You must remove the warranty sticker and 4 screws.

コメントを追加する

After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw.
  • After removing HDD bay cover, you will see another 3 screw.

コメントを追加する

Push there to release and remove upper back bezel. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel.
  • Push there to release and remove upper back bezel.

コメントを追加する

The upper front bezel is harder to remove. The upper front bezel is harder to remove. The upper front bezel is harder to remove.
  • The upper front bezel is harder to remove.

コメントを追加する

Remove 7 screws to release top cover. Remove 7 screws to release top cover. Remove 7 screws to release top cover.
  • Remove 7 screws to release top cover.

コメントを追加する

Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.
  • Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

コメントを追加する

To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable.
  • To release the laser unit disconnect this flex-cable.

コメントを追加する

One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel.
  • One flex-cable, for rubbers and the metal bezel.

コメントを追加する

Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.
  • Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

コメントを追加する

Assembling, assembling... Assembling, assembling... Assembling, assembling...
  • Assembling, assembling...

コメントを追加する

Let's test the device before fully assembling it. .

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

9 の人々がこのガイドを完成させました。

ZFix

メンバー登録日: 2013年12月09日

153,679 ポイント

431のガイドは作成済み

チーム

Master Techs Master Techs人のメンバー

Community

277 メンバー

725のガイドは作成済み

Very good job, kudos!

Kevin Borras - 返信

I have found that there are to types of lasers do you sell the second one that does not have the black screws on top but are silver. I have found the one with the silver screws has a smaller laser flex cable and plug. its for the cech-43xx

jack blevinski - 返信

コメントを追加する

統計データを表示:

過去 24時間: 4

過去 7 日: 57

過去 30 日: 171

今までの合計 17,164