はじめに

このガイドを参照して、電源を交換しましょう。

  1. PS3を裏返し、裏面を下にして置きます。
    • PS3を裏返し、裏面を下にして置きます。

    • 下部ケースから封印シールをゆっくりと剥がすと、隠れたネジカバーが表れます。

    • VOIDという文字が転写されないようにするためには、シールをゆっくりと温めて、きれいに剥がして交換します。

    コメントを追加する

  2. 金属製スパッジャーの平面側先端を使い、下部ケース端周辺の7つのネジカバーをこじ開けます。
    • 金属製スパッジャーの平面側先端を使い、下部ケース端周辺の7つのネジカバーをこじ開けます。

    コメントを追加する

    • トップカバーを下部ケースに固定している37mmプラスネジを7本外します。

    コメントを追加する

    • Blu-rayドライブの開口部下側の13.3mmT8セキュリティトルクスネジを4本外します(ネジが3本しかないモデルもあります)。

    Its 4 screws beneath the blu-ray

    Manuel - 返信

    Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening.

    Daniel Tlapa - 返信

    Can we edit this to say 4 screws?

    revanantwraith - 返信

    I made the change from three to four screws, but you're able to edit the guides as well. If you want to edit something, you can click the Edit link on the right side of any guide step, or the Edit link at the top right of the page (sandwiched in-between View and History).

    Taylor Arnicar -

    Do you guys have a guide for the PS3 Slim Model 3001A. The fan is different than this model.

    emknight04 - 返信

    3001a is basically same motherboard but cheaper plastic bd drive other than that its exactly the same until you get to the new slim line

    Robert -

    Anyone know an online retailer with a competitive price for the replacement fan?

    Jared - 返信

    My PS3 had only three Torx screws. Having four in the diagram was initially confusing. Obviously they made a mid-stream change at some point (mine is several years old now).

    corygbooker - 返信

    I've accidentally removed the ribbon cable from the blu-Ray drive and can not seem to figure out how to reconnect it. Can anyone help?

    OneIfByLand - 返信

    Take the top off the drive, connect the ribbon to the motherboard then replace the drive sliding the ribbon through the slot on the bottom of the drive and reconnect to the laser.

    KcXbox Repair -

    pls help i have to tear down my ps3 slim but the 4 srews are very hard to take it out because there is a needle in the middle pls hep

    Vincent Brabandt - 返信

    If the screw has a pin in the center, that means it is a security Torx meant to prevent tampering. To remove this screw, follow the guide I have linked below...

    http://www.instructables.com/id/Removing...

    Telpack - 返信

    • 後端からトップカバーを持ち上げ、PS3前方に向かって回転させます。

    • PS3からトップカバーを持ち上げて外します。

    コメントを追加する

    • ACインレットコネクタのロック機構をつまんで、まっすぐ持ち上げて電源から接続を外します。

    コメントを追加する

    • DC-Outケーブルをまっすぐ引き上げ、コネクタを持ち上げて、電源のソケットから外します。

    Those two screws are tight down there what do you recommend I use?

    Megan bronner - 返信

    • 電源を下部ケースに固定している7.6mmプラスネジを2本外します。

    Question: if a screw doesn't come out, what do you recommend, without potentially damaging the system, inside and out?

    kramiz2488 - 返信

    It seems these can be quite tight, but they did come loose with someextra force in my case. They did that thing where it makes cracking sounds, but nothing really breaks. They're just really tight in there. - I just wouldn't recommend taking these out too often.

    Michael Hendriks - 返信

    • 電源をPS3前部から見える左端から上方に持ち上げます。

    コメントを追加する

    • 2番目の画像で示されている2つの金属製のポストから外れるまで、電源の左端を持ち上げ続けます。

    • ケーブルが巻き込まれないよう注意しながら、PS3から電源を取り外します。

    It seems it kind of ends for me here. I can only lift the left side about an inch and then the right side stays down like it’s stuck to something underneath. It feels like I’m bending something. Could something have melted underneath?… It's really stuck, I can't get it to come loose. And I can't see much shining a light into it either. - Any tips?…

    Michael Hendriks - 返信

    I had the same issue but was able to get it off. The right side (as per the above picture) has two long column like sections that actually goes into the machine. Took me a bit of wiggling and some brute force.

    Ivan Amaro - 返信

まとめ

デバイスを再度組み立てるには、この説明書の逆の順番で組み立ててください。

36 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 貢献してみませんか?
翻訳を始める ›

Andrew Bookholt

500,810 ポイント

619のガイドは作成済み

Hello, my question is I have an american ps3 which works on 110 volts and I'm in europe where they use 220volts so if I plug my ps3 without any converters will it burn or will it wor? Because I have a laptop and it works fine will my ps3 work like that aswell?

Remigijus Untulis - 返信

Perhaps, you should check the model of your PS3 and verify online. I have the CECH-2501B model (110v) but I use it in Nigeria (220v).

N3RVE -

Need help with console or trouble shooting the problem I am in the repair and purchased used or damage consoles even get it In way I can be able to talk to people who is looking for trouble shooting on phone or email or u to choose. But any console or device I am interested in buying it so I have it on hand I have seen people pay way more 4 the part. Wene it is sometimes. New or used Console r cheaper to get the whole different devices then part for the console

Jason Ellis -

More to my comment I can be able to talk or text or email. SO you can do it yourself and it's not to bad to diy and your up to run the console after u fixed it. Do I you self. (Diy) even if people walk through it step 4 step.

Jason Ellis -

I have a PS3 Slim (CECH-3004B)

Can I install any PSU what is made for PS3 slim?

Or I should make a research what kind of PSU can be installed into my model (CECH-3004B) ?

Thank you for your help in advance ^^

Jani - 返信

My ps3 2501A was dropped while moving now it wont show up o the screen or turn off .. What can it be ?

Wendy Hernandez - 返信

Hello i was moving and my ps3 slim 2501A was dropped now it wont show up on the screen nor will it connect on hdmi or usb or anythig and it wont turn off alone what can it be?

Wendy Hernandez - 返信

i have a ps3 i bought it from the uk and i am in the usa the ps3 is 220 ait wont stay one what should i do, should i buy a 110-220 power supply

kenny jean - 返信

コメントを追加する

統計データを表示:

過去 24時間: 18

過去 7 日: 110

過去 30 日: 438

今までの合計 56,618