はじめに

このガイドを参照して、PS3のBlu-rayディスクドライブを交換しましょう。このドライブは、ソニーが特許を持っています。

  1. PS3を裏返し、裏面を下にして置きます。
    • PS3を裏返し、裏面を下にして置きます。

    • 下部ケースから封印シールをゆっくりと剥がすと、隠れたネジカバーが表れます。

    • VOIDという文字が転写されないようにするためには、シールをゆっくりと温めて、きれいに剥がして交換します。

    コメントを追加する

  2. 金属製スパッジャーの平面側先端を使い、下部ケース端周辺の7つのネジカバーをこじ開けます。
    • 金属製スパッジャーの平面側先端を使い、下部ケース端周辺の7つのネジカバーをこじ開けます。

    コメントを追加する

    • トップカバーを下部ケースに固定している37mmプラスネジを7本外します。

    コメントを追加する

    • Blu-rayドライブの開口部下側の13.3mmT8セキュリティトルクスネジを4本外します(ネジが3本しかないモデルもあります)。

    Its 4 screws beneath the blu-ray

    Manuel - 返信

    Remove the four 13.3 mm T8 security Torx screws beneath the Blu-ray drive opening.

    Daniel Tlapa - 返信

    Can we edit this to say 4 screws?

    revanantwraith - 返信

    I made the change from three to four screws, but you're able to edit the guides as well. If you want to edit something, you can click the Edit link on the right side of any guide step, or the Edit link at the top right of the page (sandwiched in-between View and History).

    Taylor Arnicar -

    Do you guys have a guide for the PS3 Slim Model 3001A. The fan is different than this model.

    emknight04 - 返信

    3001a is basically same motherboard but cheaper plastic bd drive other than that its exactly the same until you get to the new slim line

    Robert -

    Anyone know an online retailer with a competitive price for the replacement fan?

    Jared - 返信

    My PS3 had only three Torx screws. Having four in the diagram was initially confusing. Obviously they made a mid-stream change at some point (mine is several years old now).

    corygbooker - 返信

    I've accidentally removed the ribbon cable from the blu-Ray drive and can not seem to figure out how to reconnect it. Can anyone help?

    OneIfByLand - 返信

    Take the top off the drive, connect the ribbon to the motherboard then replace the drive sliding the ribbon through the slot on the bottom of the drive and reconnect to the laser.

    KcXbox Repair -

    pls help i have to tear down my ps3 slim but the 4 srews are very hard to take it out because there is a needle in the middle pls hep

    Vincent Brabandt - 返信

    If the screw has a pin in the center, that means it is a security Torx meant to prevent tampering. To remove this screw, follow the guide I have linked below...

    http://www.instructables.com/id/Removing...

    Telpack - 返信

    • 後端からトップカバーを持ち上げ、PS3前方に向かって回転させます。

    • PS3からトップカバーを持ち上げて外します。

    コメントを追加する

    • ACインレットコネクタのロック機構をつまんで、まっすぐ持ち上げて電源から接続を外します。

    コメントを追加する

  3. 20ドル以上のお買い上げで送料無料(米国内にお住まいの方対象)
    お支払い手続きの際にはクーポンコードBLUEANDBLACKを入力してください。(米国内にお住まいの方対象)
    20ドル以上のお買い上げで送料無料(米国内にお住まいの方対象)
    クーポンコードBLUEANDBLACKをご使用ください。(米国内にお住まいの方対象)
    • DC-Outケーブルをまっすぐ引き上げ、コネクタを持ち上げて、電源のソケットから外します。

    Those two screws are tight down there what do you recommend I use?

    Megan bronner - 返信

    • 電源を下部ケースに固定している7.6mmプラスネジを2本外します。

    Question: if a screw doesn't come out, what do you recommend, without potentially damaging the system, inside and out?

    kramiz2488 - 返信

    It seems these can be quite tight, but they did come loose with someextra force in my case. They did that thing where it makes cracking sounds, but nothing really breaks. They're just really tight in there. - I just wouldn't recommend taking these out too often.

    Michael Hendriks - 返信

    • 電源をPS3前部から見える左端から上方に持ち上げます。

    コメントを追加する

    • 2番目の画像で示されている2つの金属製のポストから外れるまで、電源の左端を持ち上げ続けます。

    • ケーブルが巻き込まれないよう注意しながら、PS3から電源を取り外します。

    It seems it kind of ends for me here. I can only lift the left side about an inch and then the right side stays down like it’s stuck to something underneath. It feels like I’m bending something. Could something have melted underneath?… It's really stuck, I can't get it to come loose. And I can't see much shining a light into it either. - Any tips?…

    Michael Hendriks - 返信

    I had the same issue but was able to get it off. The right side (as per the above picture) has two long column like sections that actually goes into the machine. Took me a bit of wiggling and some brute force.

    Ivan Amaro - 返信

    • ケーブルをBlu-rayドライブ本体に留めているテープがあれば剥がします。

    コメントを追加する

    • スパッジャーの平面側先端や指の爪を使い、Blu-rayリボンケーブルソケットの固定フラップを跳ね上げます。

    • ソケット自体ではなく、調節可能な固定フラップのみを触るようにしてください。

    コメントを追加する

    • Blu-rayリボンケーブルを引き上げ、ソケットから外します。

    コメントを追加する

    • Blu-ray電源ケーブルをまっすぐ引き上げ、Blu-rayドライブのソケットからコネクタを持ち上げて外します。

    コメントを追加する

    • Blu-rayドライブを下部ケースに固定している9.5mmプラスネジ1本を外します。

    コメントを追加する

    • Blu-rayドライブの右端をつまんで、少し持ち上げて、筐体からコントロール基板を取り除きます。

    • PS3からBlu-rayドライブを取り外します。

    • Blu-rayドライブを再度取り付けた後、作業を続ける前に、コントロール基板が下部ケースの上にしっかりと固定されているか必ず確認してください。

    • ブルーレイドライブを新しいドライブと交換するときは、回路基板を移し替えてください

    my cd drive has 3 cables, two by the fan, one right under, i believe i damaged the one on the bottom because it is very difficult to put back in hence the repair. But the photos here dont show the 3 cables, not sure if you have one for this model?

    Eduardo Cutino - 返信

    I followed the steps and I successfully removed my disc drive the guide was helpful but I had issues and the ribbon cables on my replacement disc drive were too short after a soddering attempt failed I now need to rebut a disc drive can someone direct me to a proper replacement with the correct size I need it's a ps3 slim 120G please help

    Nick - 返信

    I popped a friends apart to see if I could put in mine, which won't stay online for more than 1minute 10 seconds. Plays DVDs fine. Anyway, his had 3 cables and mine only has 1. How do I know which DVD player to order?

    ntdoc - 返信

    Completely different drive in my slim. 3 ribbon cables on the back that pull straight up out of their connectors. And one wide ribbon hidden underneath and almost impossible to get to. After disconnecting the 3 visible cables lift the back of the drive about 3/4" and use a plastic spudger to release the clip on the cable before lifting off the drive. Reinstalling is a nightmare. The cable has a black line to indicate how far to insert into the connector. Get it in there somehow then use the spudger to push the clip down. If it's not level release it and try again and again and again until you get it right. Sony must use some awfully small fingers when they build these ;-)

    jurquijo - 返信

    I had the same issue with the ribon feeding beneath the blu ray player. This video provided a much better solution. It requires dissassembling the blu ray: https://youtu.be/Upy2bTev3M0

    Rebel Seven - 返信

    My disk drive needs to be replaced. Your step by step is straight forward and are very helpful. At the end you mentioned “If replacing the Blu-ray drive with a new drive, swap the circuit board from your old drive into the new drive”.

    Which circuit board? Can your please add a picture of the circuit board you are referring to?

    Henry - 返信

    @hh168 There’s now a link in the text of that step, which will take you to a video with detailed instructions for swapping the board.

    Jeff Suovanen -

まとめ

デバイスを再度組み立てるには、この説明書の逆の順番で組み立ててください。

153 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 貢献してみませんか?
翻訳を始める ›

Andrew Bookholt

501,064 ポイント

619のガイドは作成済み

great work guys and ladies.......haha went without a snag!

Jesse Waterhouse - 返信

I have a question I have followed your guide properly and removed my drive and found that the laser and disc loader are both need replaced. My question is when I go online and look for the replacement it sometimes shows just the laser then others shows the driver. I want the entire component as seen in this guide above. Do these come intact with everything in it when I buy it online. Can you please help.

Thank you,

Thomas Martinez

Tomlvgmartinez@yahoo.com

Thomas Martinez - 返信

Ive been able to remove the drive and I think it's fixed. To get it back together how do you get that ribbon underneath to go back into the slot? Is there a trick? I can get it lined up, but it won't go in.

Thanks for the help

ken - 返信

Ken,

Don' t know if this helps you now after all this time, but maybe it will help others with the same issue.

a) On the slot where the ribbon is to be inserted, is a lock clip. You pull up on that (gently).

b) Slide the ribbon in now with the clip lifted.

c) While securing the ribbon down in the slot, push the clip down, it will lock the ribbon in the slot.

Hopefully this helps, I didn't realize the clip could be lifted. While it's down, it is impossible to set the ribbon in.

ShuriKen

ShuriKen -

“If replacing the Blu-ray drive with a new drive, swap the circuit board from your old drive into the new drive.” Where can I find that instruction?

Thanks

lttexan - 返信

There’s now a link in the text of that step, which will take you to a video with detailed instructions for swapping the board.

Jeff Suovanen -

Great video linked at the end to help with swapping out the circuit board, as well as the rest of the steps. Repair worked great, now we’re back in business for Blurays!

Joey Maxfield - 返信

Thank you, thank you , thank you!!! Can get back to playing the original Dark Souls after snagging it for a 10 bucks :P

final__boss - 返信

Sadly the replacement drive is typically $99… which is close to what a complete used system would cost if you bought it from someone :(

Mark H - 返信

コメントを追加する

統計データを表示:

過去 24時間: 21

過去 7 日: 209

過去 30 日: 860

今までの合計 205,447