はじめに

PlayStation 3 プラスチック製トップカバーの交換手順について説明します。

PS3の側面にあるゴム製のねじカバー(黒色)を スパッジャー(※1)の先端を用いて取り外します。 ※1 先端が細く平らになっているヘラのような工具
  • PS3の側面にあるゴム製のねじカバー(黒色)を スパッジャー(※1)の先端を用いて取り外します。 ※1 先端が細く平らになっているヘラのような工具

  • ねじカバーには封印シールが張られています。この封印シールをはがすと「VOID」という文字がシールに表示されます。

コメントを追加する

セキュリティートルクスねじ(T10   8.5mm)を 外します。
  • セキュリティートルクスねじ(T10 8.5mm)を 外します。

コメントを追加する

  • スマートプレートをハードドライブベイの方向へスライドさせ、PS3本体から持ち上げて外します。

コメントを追加する

  • トップカバーには固定されていない金属製の小さなブラケット(ねじ受け)があります。よって紛失しないよう注意して下さい。

That small metal bracket/socket set up looks completely different in the ps3 I'm working on. Model: CECHK01.

Any suggestions?

Marcus - 返信

  • 7箇所のねじを取り外します。

    • プラスねじ(Phillips 52mm) x6

    • プラスねじ(Phillips 30mm) x1

2 more smaller screws (don't know what size...small) just below the top middle screw and top right screw (in the picture). Look for the arrows...

E Goo - 返信

after you remove the screws, you may have to push a tab to take the cover off if you meet resistance on one side of the cover. Here is a link to a video that explains it, saved me lots of trouble:

http://youtu.be/jZgekNsRB-A?t=1m54s

ericksi33 - 返信

Thanks @ericksi33, this really helped me out.

hogurt -

1st attempt, fan loud. Ps3 lasted about 2 wks. 2nd attempt noticed very poor contact between heatsink & cpu,gpu when taking it apart. Research - Found a better way to apply thermal past. I personally disapprove of guide on this. A small bit about the size of a grain of rice in center of cpu is plenty. Clamp the heat sinks back on. Then take it apart & check contact area. Thermal paste should have spread to about the size of a quarter.(more is better. Less then a nickel size is poor contact) possibly weak clamps. Carefully applied pressure onto the cpu & gpu, pressing them into the heatsinks before clamping heatsink clamps on. Achieved greater then quarter sized thermal past spread. Fan silent in comparison & ps3 lasted about a yr. Rarely did I ever hear the fan go to high and get loud after that. About to begin my third fix on this same ps3. One of the first 80g backwards compatible. other then those notes and that this guide was for a different model ps3 (minor differences) I liked this guide. easy to follow.

brettgomes - 返信

Although the battery is described as proprietary, it looks like it is the common CR2032 lithium coin battery that is used in calculators and some computers. I haven't had to replace mine but I suspect under the heatshrink cover is a battery holder which will allow the coin battery to be removed and replaced. Then wrap with electrical tape and reinstall.

RickP - 返信

I tried this with the heatgun and it ruined my PS3. The CPU and GPU are NOW RUINED!!! It did not work for and made things worst!!! I sent it to a place to get reballed and they said the HEATGUN had overheated my processor and killed them!!! So think twice about doing this. Just because it is already broken, DON'T THINK YOU CAN'T MAKE IT WORST!

georgehollyoh - 返信

Why would you try it with a heat gun, no were is it mentioned to do that

Phillip Pereira -

There are 2 additional screws to remove , front center and front left , just behind the already marked screws.

mikentc90 - 返信

  • トップカバーをリアカバー端から持ち上げて、PS3の正面側に向けてこれを回します。

  • 上部カバーを取り外します。

Disconnect the memory card ribbon cable.

Tobias Stockmann - 返信

The top would hardly budge on the left back corner and was stuck on the right back corner. There is a plastic hook that needs to be unfastened to lift the top off. It is located in a hole on the top back corner on the right hand side, so the corner straight across the on off button. Just gently push the plastic hook a bit front the rear of the machine with a spudger. It gives easily and the top will be free to lift off after that.

cornellg - 返信

まとめ

再組み立てする手順については、本手順を逆に実施して下さい。

40 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 貢献してみませんか?
翻訳を始める ›

Walter Galan

565,064 ポイント

1,203のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 10

過去 7 日: 46

過去 30 日: 230

今までの合計 33,755