はじめに

This guide will show how to replace the eyes and eye wire if either are damaged.

パーツ

Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side. Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side.
  • Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side.

コメントを追加する

Pull the grip away from the frame. Pull the grip away from the frame.
  • Pull the grip away from the frame.

コメントを追加する

Pull the grip through the opening. The grip is connected in the middle and is one piece.
  • Pull the grip through the opening.

  • The grip is connected in the middle and is one piece.

コメントを追加する

Remove the macroline from the fitting by pulling the metal ring around the end of the fitting away while pulling out the macroline. It helps to rotate the collar to create room to pull out macroline. It helps to rotate the collar to create room to pull out macroline.
  • Remove the macroline from the fitting by pulling the metal ring around the end of the fitting away while pulling out the macroline.

    • It helps to rotate the collar to create room to pull out macroline.

コメントを追加する

While pulling in the metal ring on the fitting, pull the macroline out. While pulling in the metal ring on the fitting, pull the macroline out. While pulling in the metal ring on the fitting, pull the macroline out.
  • While pulling in the metal ring on the fitting, pull the macroline out.

コメントを追加する

Use 1/8" allen wrench to remove screw behind regulator. Use 1/8" allen wrench to remove screw behind regulator. Use 1/8" allen wrench to remove screw behind regulator.
  • Use 1/8" allen wrench to remove screw behind regulator.

コメントを追加する

Use 1/8" allen wrench to loosen the screw inside the grip on the right side. The screw only needs to be turned a couple of times. Slide the upper frame forward on the rails and remove the screw from the slot to separate the two halves of the body.
  • Use 1/8" allen wrench to loosen the screw inside the grip on the right side.

    • The screw only needs to be turned a couple of times.

  • Slide the upper frame forward on the rails and remove the screw from the slot to separate the two halves of the body.

  • BE CAREFUL: Do not pull the two frames apart too much or too quickly. This may cause the wires to be damaged.

コメントを追加する

Use a prying tool or tweezers to gently remove the connection from the board. It is the connection with 2 black and 2 red wires. Pull the wire through the opening. Pull the wire through the opening.
  • Use a prying tool or tweezers to gently remove the connection from the board. It is the connection with 2 black and 2 red wires.

  • Pull the wire through the opening.

コメントを追加する

Use 5/64" allen key to remove each screw from eye covers (Located on both sides of the paintball marker.) Pull off eye covers. (Located on both sides of the paintball marker.) Pull off eye covers. (Located on both sides of the paintball marker.)
  • Use 5/64" allen key to remove each screw from eye covers (Located on both sides of the paintball marker.)

  • Pull off eye covers. (Located on both sides of the paintball marker.)

コメントを追加する

Gently pull out the two eyes, one on each side of the paintball marker. The red wire leading to the eye on the right side of the paintball marker.  The black wire leads to the eye on the left side. The red wire leading to the eye on the right side of the paintball marker.  The black wire leads to the eye on the left side.
  • Gently pull out the two eyes, one on each side of the paintball marker.

    • The red wire leading to the eye on the right side of the paintball marker. The black wire leads to the eye on the left side.

コメントを追加する

まとめ

To reassemble your device with a new eye wire, follow this guide in reverse.

Rett Triplett

メンバー登録日: 2013年10月18日

801 ポイント

8のガイドは作成済み

チーム

Clemson, Team 13-6, Benson Fall 2013 Clemson, Team 13-6, Benson Fall 2013人のメンバー

CLEM-BENSON-F13S13G6

3 メンバー

8のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 7

今までの合計 713