メインコンテンツにスキップ

はじめに

The motherboard is fairly simple to remove. No special tools are needed besides a screwdriver to open up the SmartBowl. Be careful when handling the motherboard because the components on it are very delicate.

パーツ

パーツは指定されていません。

  1. Eject the SmartBowl by pressing the button located at the front of the SmartFeeder base. Remove the metal tray by using both hands and pulling out the bowl towards you. Remove the metal tray by using both hands and pulling out the bowl towards you.
    • Eject the SmartBowl by pressing the button located at the front of the SmartFeeder base.

    • Remove the metal tray by using both hands and pulling out the bowl towards you.

  2. Turn the bowl tray side down by using both hands. Remove seven 11 mm screws by using the Phillips #1 screwdriver.
    • Turn the bowl tray side down by using both hands.

    • Remove seven 11 mm screws by using the Phillips #1 screwdriver.

  3. Take the battery out of the SmartBowl with tweezers, avoid pulling on any wires. Hold the SmartBowl down using one hand while using the other hand to remove the battery.
    • Take the battery out of the SmartBowl with tweezers, avoid pulling on any wires.

    • Hold the SmartBowl down using one hand while using the other hand to remove the battery.

  4. iPhone X用修理キット

    Warranty up? No worries, we’ve got the fix.

    ショップを見る

    iPhone X用修理キット

    Warranty up? No worries, we’ve got the fix.

    ショップを見る
  5. Remove the tape, closest to the four white connectors, with your hands. Keep the wires attached to the tape for easy reassembly.
    • Remove the tape, closest to the four white connectors, with your hands.

    • Keep the wires attached to the tape for easy reassembly.

  6. Trace the wires with your hands from the battery to the motherboard. Detach the three-prong connector between the battery and the motherboard by pulling the white connectors with your hands.
    • Trace the wires with your hands from the battery to the motherboard.

    • Detach the three-prong connector between the battery and the motherboard by pulling the white connectors with your hands.

    • Hold on to the sockets on the motherboard or you could accidentally pull off the entire assembly.

  7. Remove the remaining 3-prong connectors by carefully pulling outwards.
    • Remove the remaining 3-prong connectors by carefully pulling outwards.

    • Hold on to the sockets on the motherboard or you could accidentally pull off the entire assembly.

  8. Push both small gray pieces next to the ribbon connector towards the ribbon to put them in the “open” position using the nylon spudger. Push both small gray pieces next to the ribbon connector towards the ribbon to put them in the “open” position using the nylon spudger.
    • Push both small gray pieces next to the ribbon connector towards the ribbon to put them in the “open” position using the nylon spudger.

  9. Remove the ribbon connector from its slot by pulling on it with a couple fingers. The ribbon should come out easily with the gray pieces in the "open" position.  Do not use too much force with the ribbon or it could be damaged.
    • Remove the ribbon connector from its slot by pulling on it with a couple fingers.

    • The ribbon should come out easily with the gray pieces in the "open" position. Do not use too much force with the ribbon or it could be damaged.

    • Make sure the gray pieces are in the “open” position when you reassemble the ribbon connector or the connector will not go into its slot. Once the connector is in the slot, slide the gray tabs back down into the “closed” position

まとめ

To reassemble your device, follow these instructions in reverse order.

Travis Lamb

メンバー登録日: 2018年10月08日

97 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team S13-G7, White Fall 2018 Cal Poly, Team S13-G7, White Fall 2018人のメンバー

CPSU-WHITE-F18S13G7

4 メンバー

5のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 2

今までの合計 60