Panasonic PV-GS9 outercasing replacement

作成者： Trevor Johnson (そして 9 人のその他投稿者)

コメント: 0
お気に入り: 1
完了: 1

Panasonic PV-GS9 outercasing replacement

難易度

普通

手順

所要時間

10 - 15 分

はじめに

In order to repair the problems that may arise while using the Panasonic PV-GS9 you must disassemble the camcorder entirely. This will allow you to have three large pieces of the camcorder from which all the repairs can be made.

ツール

これらのツールを購入する

Phillips #00 Screwdriver

$6.99

購入する
Spudger

$2.99

購入する

パーツ

パーツは必要ありません。

手順1 Outer Casing

Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder.

Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder.

翻訳

手順2

Using a #00 Phillips head screwdriver, remove the two 4.5mm screws from the camcorder.

Open the tape compartment.
Using a #00 Phillips head screwdriver, remove the two 4.5mm screws from the camcorder.

翻訳

手順3

Use a plastic opening tool to remove the gray trim piece from top of the camcorder.

Take care when removing the trim piece. The plastic parts are fragile and can break easily.

Use a plastic opening tool to remove the gray trim piece from top of the camcorder.
Take care when removing the trim piece. The plastic parts are fragile and can break easily.

翻訳

手順4

Rotate the camcorder so that the eye piece is facing you, and remove the battery. Remove the four black 4.5mm screws, which sit behind the battery. Then, remove the 5th screw to the right of the battery dock.

Rotate the camcorder so that the eye piece is facing you, and remove the battery. Remove the four black 4.5mm screws, which sit behind the battery. Then, remove the 5th screw to the right of the battery dock.
Be careful not to lose any screws whilst trying to remove them.

翻訳

手順5

Rotate the camcorder so that the tape compartment is facing you. Remove the single 4.5mm black screw, which is above the hook for the hand strap.

It may help you during this step to undo the strap on one end.

Rotate the camcorder so that the tape compartment is facing you. Remove the single 4.5mm black screw, which is above the hook for the hand strap.
It may help you during this step to undo the strap on one end.
Next, rotate the camcorder so that the lens is facing you. Remove the single 4.5mm black screw from the front panel.

翻訳

手順6

Rotate the camcorder so that the bottom is facing towards you. Remove the single remaining 4.5mm black screw from the bottom.

Next, while still having the bottom of the camcorder facing you, remove the four silver 4.5mm screws from the body.

Rotate the camcorder so that the bottom is facing towards you. Remove the single remaining 4.5mm black screw from the bottom.
Next, while still having the bottom of the camcorder facing you, remove the four silver 4.5mm screws from the body.

翻訳

手順7

Open the LCD screen on the side of the camcorder.

Open the LCD screen on the side of the camcorder.
Using a #00 screwdriver, remove the two 4.5mm silver screws located on either side of the hinge of the LCD screen.

翻訳

手順8

Very carefully remove the front cover from the main body of the camcorder.

This should come apart with relative ease, however a plastic opening tool may help you remove this panel a little more easily.

Very carefully remove the front cover from the main body of the camcorder.
This should come apart with relative ease, however a plastic opening tool may help you remove this panel a little more easily.
There is a ribbon cable attached to the front panel and the camcorder body, so be careful not to pull that off when you remove this panel.