メインコンテンツにスキップ

Panasonic Lumix DMC-TZ5 button board Replacement

必要な工具と部品

  1. Panasonic Lumix DMC-TZ5 button board Replacement, Back Cover: 手順 1、 1の画像 1
    • Remove the battery and memory card from the device.

  2. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 2、 1の画像 1
    • Remove 4 screws from the right side of the camera.

    • There are two 3.4mm screws at the top.

    • There are two 2.2mm screws at the bottom.

  3. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 3、 1の画像 1
    • Remove the single 3.4mm screw on the left side of the camera.

  4. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 4、 1の画像 1
    • Remove 5 screws from the base of the camera.

    • There are two 2.2mm screws next to the battery compartment.

    • There are three 4mm screws around the tripod mount.

  5. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 5、 1の画像 1
    • Slowly slide the back cover away from the device

    • The back casing is held in place by two ribbon cables. Do not pull the back cover too far from the camera.

  6. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 6、 2の画像 1 Panasonic Lumix DMC-TZ5 button board Replacement: 手順 6、 2の画像 2
    • Detach both ribbon cables using a spudger.

    • Use the tip of the spudger to lift the black clip upward, unlocking the ribbon cable.

  7. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 7、 1の画像 1
    • Remove the back casing from the camera.

  8. Panasonic Lumix DMC-TZ5 button board Replacement, button board: 手順 8、 2の画像 1 Panasonic Lumix DMC-TZ5 button board Replacement, button board: 手順 8、 2の画像 2
    • Use the spudger to remove the ribbon cable connecting the lens casing to the circuit board by lifting up the black clip.

    • Carefully remove the function switch cover. This unit snaps on and off.

  9. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 9、 1の画像 1
    • Carefully unsnap the front logic board from the rear logic board using a spudger.

  10. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 10、 2の画像 1 Panasonic Lumix DMC-TZ5 button board Replacement: 手順 10、 2の画像 2
    • Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera.

  11. Panasonic Lumix DMC-TZ5 button board Replacement: 手順 11、 3の画像 1 Panasonic Lumix DMC-TZ5 button board Replacement: 手順 11、 3の画像 2 Panasonic Lumix DMC-TZ5 button board Replacement: 手順 11、 3の画像 3
    • Remove the ribbon cable from the top connection panel by unlocking the black clip with a spudger.

    • This leaves you with the logic board and the top connection panel separate and free from the camera

終わりに

To reassemble your device, follow these instructions in reverse order.

作成者

4人の作成者と共同で作成されました。

Ben Canfield

メンバー登録日: 10/10/10

409 ポイント

3のガイドは作成済み

チーム

Cal Poly, Team 9-21, Regan Fall 2010 Cal Poly, Team 9-21, Regan Fall 2010人のメンバー

CPSU-REGAN-F10S9G21

4 メンバー

14のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 4

今までの合計 5,592