メインコンテンツにスキップ

パーツ

パーツは指定されていません。

  1. この手順は未翻訳です。 翻訳を手伝う。

    Eject the disk tray from the DVD player before removing power supply.
    • Eject the disk tray from the DVD player before removing power supply.

  2. この手順は未翻訳です。 翻訳を手伝う。

    Evenly lift upward on the disk tray front cover (not slanted, as pictured). This will allow for easier dissasembly of the player.
    • Evenly lift upward on the disk tray front cover (not slanted, as pictured). This will allow for easier dissasembly of the player.

  3. この手順は未翻訳です。 翻訳を手伝う。

    Remove 3 screws running along back edge of case cover. Remove 2 screws from each side of case cover.
    • Remove 3 screws running along back edge of case cover.

    • Remove 2 screws from each side of case cover.

  4. この手順は未翻訳です。 翻訳を手伝う。

    Grab edges of cover, pull outward slightly, and pull straight up.
    • Grab edges of cover, pull outward slightly, and pull straight up.

  5. この手順は未翻訳です。 翻訳を手伝う。

    Lift up the 5 tabs securing the front panel to the chassis. There are 3 on the bottom, and 2 on the inside edges of the panel. Panel should then lift off the player. Lift up the 5 tabs securing the front panel to the chassis. There are 3 on the bottom, and 2 on the inside edges of the panel. Panel should then lift off the player.
    • Lift up the 5 tabs securing the front panel to the chassis. There are 3 on the bottom, and 2 on the inside edges of the panel. Panel should then lift off the player.

  6. この手順は未翻訳です。 翻訳を手伝う。

    Locate the 4 screws securing the disk drive assembly. There are two on each side. Use a narrow screwdriver to remove all 4 screws. Remove the blue ribbon wire from its connector. When doing this, be cautious to not damage the connector.
    • Locate the 4 screws securing the disk drive assembly. There are two on each side.

    • Use a narrow screwdriver to remove all 4 screws.

    • Remove the blue ribbon wire from its connector. When doing this, be cautious to not damage the connector.

  7. この手順は未翻訳です。 翻訳を手伝う。

    Lift assembly by the front to pull metal bracket from the power board.
    • Lift assembly by the front to pull metal bracket from the power board.

    • Pull up back end and lift drive out.

  8. この手順は未翻訳です。 翻訳を手伝う。

    With the drive assembly separate from the player, hold as shown and pull the bracket edges away from the disk drive.
    • With the drive assembly separate from the player, hold as shown and pull the bracket edges away from the disk drive.

    • Lift bracket off and reserve for re-assembly.

ゴール

2 の人々がこのガイドを完成させました。

William

メンバー登録日: 2011年04月26日

250 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 18-20, Garner Spring 2011 Cal Poly, Team 18-20, Garner Spring 2011人のメンバー

CPSU-GARNER-S11S18G20

4 メンバー

11のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 15

今までの合計 5,063