メインコンテンツにスキップ

修理を始めるには

修理する権利

パーツ&ツール

はじめに

Prerequisite Only

This guide will show you how to remove the back panel of the camera so that you can access the inside.

Before you begin, make sure that the battery and SD card have been removed from the camera.

  1. All screws should be removed using a Phillips #0 screwdriver. Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.
    • All screws should be removed using a Phillips #0 screwdriver.

    • Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.

  2. Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there. Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.
    • Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.

  3. Turn the camera upside down and  unscrew the three 5mm screws found on the bottom. Turn the camera upside down and  unscrew the three 5mm screws found on the bottom.
    • Turn the camera upside down and unscrew the three 5mm screws found on the bottom.

  4. Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ

    Nintendo Switch 修理キット

    ゲームを再開するための、早くて簡単な修理キット

    Switch 修理キットページへ
  5. On the top of the camera  locate the two rails with a thin sheet of metal on the floor between them. With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.
    • On the top of the camera locate the two rails with a thin sheet of metal on the floor between them.

    • With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.

  6. Proceed to remove the four 5mm Phillips screws that you just uncovered.
    • Proceed to remove the four 5mm Phillips screws that you just uncovered.

  7. Slowly pull on both side of the camera, until both halves begin to separate from each other.
    • Slowly pull on both side of the camera, until both halves begin to separate from each other.

    • Do not pull too hard, as both halves are held together with ZIF connector cables.

  8. Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard. Carefully pull the ribbon cables out of the slot once they have been released. Only the two indicated connectors need to be removed to separate the two halves of the camera.
    • Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard.

    • Carefully pull the ribbon cables out of the slot once they have been released.

    • Only the two indicated connectors need to be removed to separate the two halves of the camera.

終わりに

To reassemble your device, follow these instructions in reverse order.

Alberto Rodriguez

メンバー登録日: 2017年01月24日

485 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 21-3, Maness Winter 2017 Cal Poly, Team 21-3, Maness Winter 2017人のメンバー

CPSU-MANESS-W17S21G3

6 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 2

過去 30 日: 9

今までの合計 269