はじめに

This guide show you how to remove and replace the Palm Centro's speakers

パーツ

パーツは必要ありません。

Press and slide open the battery cover. Press and slide open the battery cover.
  • Press and slide open the battery cover.

コメントを追加する

Caution: Turn cell phone off before removing battery!
  • Caution: Turn cell phone off before removing battery!

  • Press battery to the right.

  • Then lift up battery pack to remove.

コメントを追加する

Phone with battery removed
  • Phone with battery removed

コメントを追加する

Remove the touchpad pen from the top left corner on the back to reveal the last of 6 screws to be removed.
  • Remove the touchpad pen from the top left corner on the back to reveal the last of 6 screws to be removed.

コメントを追加する

Lift the rubber cap at the top right to reveal the sixth screw.
    • Lift the rubber cap at the top right to reveal the sixth screw.

    • Caution: There is a small Palm sticker under the rubber cap. Tampering with or removing this sticker will void your warranty!

    • Remove the six screws using the T5 Torx screwdriver.

コメントを追加する

Remove the SIM card so housing can be separated. Remove the SIM card so housing can be separated.
  • Remove the SIM card so housing can be separated.

コメントを追加する

Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert. Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert.
  • Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert.

コメントを追加する

Remove the small plastic insert at the bottom of the phone. Remove the small plastic insert at the bottom of the phone.
  • Remove the small plastic insert at the bottom of the phone.

コメントを追加する

Continue with plastic pry tool all the way around the phone to remove the back housing. Continue with plastic pry tool all the way around the phone to remove the back housing.
  • Continue with plastic pry tool all the way around the phone to remove the back housing.

コメントを追加する

Carefully peel back the tape holding the speaker (left) and keyboard (right) connection tabs in place.
  • Carefully peel back the tape holding the speaker (left) and keyboard (right) connection tabs in place.

コメントを追加する

Using the plastic prying tool, lift the tabs and carefully pull the contact connections out on both sides.
  • Using the plastic prying tool, lift the tabs and carefully pull the contact connections out on both sides.

    • Be very careful, these electronics are delicate!

コメントを追加する

Separate the logic board from the case by lifting and pulling out the bottom.
  • Separate the logic board from the case by lifting and pulling out the bottom.

コメントを追加する

Pry the four plastic latches free that connect the antenna to the logic board. Excessive force may damage your logic board! Remove the antenna from the logic board.
  • Pry the four plastic latches free that connect the antenna to the logic board.

    • Excessive force may damage your logic board!

  • Remove the antenna from the logic board.

コメントを追加する

The internal speaker is attached to the antenna. To remove it, pry the speaker from the antenna using the tip of your screwdriver.
  • The internal speaker is attached to the antenna. To remove it, pry the speaker from the antenna using the tip of your screwdriver.

    • The speaker should be placed back into its spot in the correct position. Take notice of the gold connectors

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Kevin

メンバー登録日: 2010年04月12日

31 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 15-49, Garner Spring 2010 Cal Poly, Team 15-49, Garner Spring 2010人のメンバー

CPSU-GARNER-S10S15G49

5 メンバー

12のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 1

今までの合計 1,390