はじめに
PSPのよくある破損の一つとして、UMDバックパネルが揺れたり緩んで外れてしまうことがあります。
このガイドではUMDバックパネル部分の修理方法を説明しています。
必要な工具と部品
-
-
PSP裏面左側のバッテリーケースボタンの位置を確認します。
-
ボタンを押下し、バッテリーカバーを取り外します。
You are dumbbb... BRO YOUR DUMB BC U DIDNT HAVE TO USE A TOOL TO OPEN THE DOOR. USE YOUR FINGER""
The battery door can be damaged dont use a tool
That also happend to me it got destroyed by screwdriver
-
-
-
指を使い、画像のようにバッテリーを本体から取り出します。
The use of the opening tool is completely unnecessary. There is a finger actuated opening latch button that says “PUSH” on it. Simply press down with your thumb then slide your thumb down and away, dragining the battery door with it. It will then come off. Assuming the system still has its original plastics, they may have become brittle enough that the opening tool could damage the release button or the plastic cover.
-
-
-
#00プラスドライバーで画像で示されている4本のネジを外します。
you need to peel back the warranty sticker in order to access both the lower left and lower left screws
This is a bit misleading, you should only remove the two black screws in the battery compartment. The silver ones can stay.
iFixit screwdriver bits aren't thin enough to reach the two screws on the right near the memory stick slot.
Can't edit previous comment so here's a new one:
Standard or older iFixit screwdriver bits aren't thin enough to reach the two screws on the right near the memory stick slot. You'll need precision bits that have longer tips to reach these deep screws.
-
-
-
-
前の手順で引っ掛けたところが外れないように注意し、UMDドライブを慎重に閉じてください。
-
最初にバックパネルの左側のヒンジを固定し、その後右側のヒンジを固定してください。(※注意! ヒンジ部分はとても折れやすいため、あまり力を入れすぎないようによく注意をしてはめてください。)
-
固定するときは道具は要りませんが、マイナスドライバーのように先が平らなものを使っても良いです。
I try to do reshell, and one of the spring on the umd door i forcely take it out and I notice that I can shape it back as original shape.
-
再組み立てしたいときはこのガイドの手順と逆の順序から行ってください。
※注意
UMDバックパネルの爪はとても折れやすいため、つける際は十分に注意してください!
再組み立てしたいときはこのガイドの手順と逆の順序から行ってください。
※注意
UMDバックパネルの爪はとても折れやすいため、つける際は十分に注意してください!
36 の人々がこのガイドを完成させました。
以下の翻訳者の皆さんにお礼を申し上げます:
100%
これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 あなたも貢献してみませんか?
翻訳を始める ›
4 件のコメント
Hi, my UMD door opens too easily, just as i touch it sometimes, and i have to press it hard to close it. What should i do to make it stay close? i don’t understand why it has become so loose
You can actually use a file and an exacto knife and some sandpaper on an aftermarket door. They tried to make an L-shaped reinforcement on the right side (if looking at the PSP from the back) that's why it's quite hard to get it in past those screws, just shave and file and sliver little by little, until it fits in without even having to take off the front case. You may also have to do some trimming and gluing of the latch catch on most of these aftermarket UMD doors.