はじめに

This guide will show you how to remove and replace your PSP speakers.

  1. Turn the PSP over so its back is facing you.
    • Turn the PSP over so its back is facing you.

    コメントを追加する

  2. Locate the battery casing button on the rear-left side of the PSP.
    • Locate the battery casing button on the rear-left side of the PSP.

    • Press down the button and remove the battery cover.

    コメントを追加する

    • Using your finger, remove the battery upwards from the system as shown.

    コメントを追加する

    • Remove the four screws shown with a Phillips #00 screwdriver.

    • You will have to peel back the guarantee sticker to access the screw on the lower left.

    Much luck to you if you have a tiny, metal screwdriver like I did, the screws might be stuck in there and may require some force.

    Squib - 返信

    • Remove the screw from the bottom side of the PSP. Keep it separated from the rest of the screws.

    • Remove screws from back righthand side within the holes.

    コメントを追加する

    • Gently separate the outer plastic casing from the rest of the system as shown.

    コメントを追加する

    • The Button Board, at the base of the LCD Screen, is held by two clips.

    • Pry these clips over the nubs using a PSP opening tool. This will release the clips.

    • The Button Board is still attatched to the PSP by a ribbon cable!

    コメントを追加する

    • The Button Board Ribbon Cable is held down with a latch. Lift the latch open, away from the ribbon cable.

    • Pull the cable away from the latch.

    コメントを追加する

    • The LCD Screen is held by the LCD Frame with similar clips. Slide a thin tool between the clip and the screen and gently pry them apart while beginning to lift the screen.

    コメントを追加する

    • The LCD screen is still attached with ribbon cables. Gently lift up the LCD screen so you do not break them.

    コメントを追加する

    • The thin Ribbon Cable opens from the opposite side in which the Ribbon Cable enters. Open up the latch towards the Ribbon Cable. The latch will pull up and release the ribbon cable. Put your tool behind the black part, then pry up the black piece of plastic.

    • The wide Ribbon Cable opens from the same side in which the Ribbon Cable attatches, and opens away from the cable.

      • Both of these latches are the black pieces.

    • Gently pull the ribbon cables away from the latches. The LCD screen can now be removed.

    • When reassembling - be careful which way you push the latches. The small one is very easy to break.

    コメントを追加する

    • Remove the screws on the top and bottom of the frame. Be sure to keep track of where you took each screw out of.

    コメントを追加する

    • After the screws are removed, the bottom of the LCD frame will rise.

    • Open up the UMD Drive, and then slide the top of the LCD frame slightly to the right while pulling out.

    コメントを追加する

    • The speakers will now be exposed.

    コメントを追加する

    • The speakers should slide out fairly easily; it may be helpful to use tweezers to begin prying them out.

    コメントを追加する

    • Gently unplug the speakers from the socket. The speakers are completely detatched when they are unplugged from the logic board.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

8 の人々がこのガイドを完成させました。

Chris

メンバー登録日: 2010年01月14日

1,707 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 5-6, Forte Winter 2010 Cal Poly, Team 5-6, Forte Winter 2010人のメンバー

CPSU-FORTE-W10S5G6

5 メンバー

9のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 3

過去 7 日: 21

過去 30 日: 58

今までの合計 19,873