はじめに

This guide will help you replace the LCD screen if it has been cracked or damaged.

Turn the PSP over so its back is facing you.
  • Turn the PSP over so its back is facing you.

コメントを追加する

Locate the battery casing button on the rear-left side of the PSP. Press down the button and remove the battery cover.
  • Locate the battery casing button on the rear-left side of the PSP.

  • Press down the button and remove the battery cover.

コメントを追加する

Using your finger, remove the battery upwards from the system as shown. Using your finger, remove the battery upwards from the system as shown.
  • Using your finger, remove the battery upwards from the system as shown.

コメントを追加する

Remove the four screws shown with a Phillips #00 screwdriver. You will have to peel back the guarantee sticker to access the screw on the lower left.
  • Remove the four screws shown with a Phillips #00 screwdriver.

  • You will have to peel back the guarantee sticker to access the screw on the lower left.

Much luck to you if you have a tiny, metal screwdriver like I did, the screws might be stuck in there and may require some force.

Squib - 返信

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Remove the screw from the bottom side of the PSP. Keep it separated from the rest of the screws.
  • Remove the screw from the bottom side of the PSP. Keep it separated from the rest of the screws.

  • Remove screws from back righthand side within the holes.

コメントを追加する

Gently separate the outer plastic casing from the rest of the system as shown. Gently separate the outer plastic casing from the rest of the system as shown.
  • Gently separate the outer plastic casing from the rest of the system as shown.

コメントを追加する

The Button Board, at the base of the  LCD Screen, is held by two clips.
  • The Button Board, at the base of the LCD Screen, is held by two clips.

  • Pry these clips over the nubs using a PSP opening tool. This will release the clips.

  • The Button Board is still attatched to the PSP by a ribbon cable!

コメントを追加する

The Button Board Ribbon Cable is held down with a latch.  Lift the latch open, away from the ribbon cable. Pull the cable away from the latch. Pull the cable away from the latch.
  • The Button Board Ribbon Cable is held down with a latch. Lift the latch open, away from the ribbon cable.

  • Pull the cable away from the latch.

コメントを追加する

The LCD Screen is held by the LCD Frame with similar clips.  Slide a thin tool between the clip and the screen and gently pry them apart while beginning to lift the screen. The LCD Screen is held by the LCD Frame with similar clips.  Slide a thin tool between the clip and the screen and gently pry them apart while beginning to lift the screen.
  • The LCD Screen is held by the LCD Frame with similar clips. Slide a thin tool between the clip and the screen and gently pry them apart while beginning to lift the screen.

コメントを追加する

The LCD screen is still attached with ribbon cables.  Gently lift up the LCD screen so you do not break them.
  • The LCD screen is still attached with ribbon cables. Gently lift up the LCD screen so you do not break them.

コメントを追加する

The thin Ribbon Cable opens from the opposite side in which the Ribbon Cable enters. Open up the latch towards the Ribbon Cable. The latch will pull up and release the ribbon cable. Put your tool behind the black part, then pry up the black piece of plastic. The wide Ribbon Cable opens from the same side in which the Ribbon Cable attatches, and opens away from the cable. Both of these latches are the black pieces.
  • The thin Ribbon Cable opens from the opposite side in which the Ribbon Cable enters. Open up the latch towards the Ribbon Cable. The latch will pull up and release the ribbon cable. Put your tool behind the black part, then pry up the black piece of plastic.

  • The wide Ribbon Cable opens from the same side in which the Ribbon Cable attatches, and opens away from the cable.

    • Both of these latches are the black pieces.

  • Gently pull the ribbon cables away from the latches. The LCD screen can now be removed.

  • When reassembling - be careful which way you push the latches. The small one is very easy to break.

コメントを追加する

ゴール

56 の人々がこのガイドを完成させました。

Henry Lee

メンバー登録日: 2010年01月14日

548 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 5-6, Forte Winter 2010 Cal Poly, Team 5-6, Forte Winter 2010人のメンバー

CPSU-FORTE-W10S5G6

5 メンバー

6のガイドは作成済み

I broke one of the laches....helppp!!!!

janet - 返信

This is not easy...I tore up the outer casing trying to do this. I better see money in the mail for this

Justin Autrey - 返信

My Sony PSP has just stop coming on

lil bao - 返信

People!! If you weren't gifted in screws and bolts, then bring your console to a repair shop. Seriously blaming this for your Dick Fingers?

janisfranckevics - 返信

It needs to be mentioned that the power switch is very fragile. When reassembling the front cover you need to first make sure that the small black switch on the circuit board sits in the yellow part of the switch, otherwise when you apply pressure to click the cover back in place the black switch will break off.

Isak - 返信

Great tutorial, thanks to this I manage to fix the R button, it turns out the ribbon cable of the right section of buttons was dirty and a little bit off of place, and taking out the screen was necessary to get to that connector.

Jhosttyn Medina - 返信

コメントを追加する

統計データを表示:

過去 24時間: 13

過去 7 日: 105

過去 30 日: 421

今までの合計 51,501