修理を始めるには コミュニティ ストア

PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement

はじめに

Caution: This guide includes using a soldering iron and can damage your controller or your hand if not used properly.

必要な工具と部品

  1. PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement, Case: 手順 1、 2の画像 1 PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement, Case: 手順 1、 2の画像 2

    • Loosen the seven 11 mm Phillips #0 screws located on the back of the controller.

    編集

  2. PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement: 手順 2、 1の画像 1

    • Using a plastic opening tool, pry the back cover from the front.

    • The covers should separate without needing a plastic opening tool, but in some cases you may need to use it.

    編集

  3. PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement: 手順 3、 1の画像 1

    • Remove the top cover from the bottom and place next to each other.

    編集

  5. PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement, Vibration Motors: 手順 4、 2の画像 1 PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement, Vibration Motors: 手順 4、 2の画像 2

    • Lift the Logic Board and remove the rumble motors from the base of the controller.

    編集

  6. PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement: 手順 5、 1の画像 1

    • The rumble motors are located in the bottom right and left hand corners of the controller.

    • Find where the power (red) wire and ground (black) wire are connected to the logic board. The power (red) wire should be on the left while the black (ground) wire is on the right.

    編集

  7. PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement: 手順 6、 1の画像 1

    • The soldering iron is very hot and can harm you or the device if used improperly.

    • Take the soldering iron after it has been heated up and place it where the ground (black) wire is connected to the logic board.

    • Let it heat up and remove some of the solder with the solder vacuum.

    • Do the same for the power (red) wire.

    編集

  8. PDP Afterglow Wired Xbox 360 Controller Vibration Motors Replacement: 手順 7、 1の画像 1

    • Now take the new rumble motor and place the power (red) wire on the right hole where the (+) sign is.

    • Take some solder and seal the hole so that the solder is completely covering the (+) hole.

    • Do the same for the ground wire.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

4人の作成者と共同で作成されました。

Austin Miller

メンバー登録日: 09/18/15

192 ポイント

1ガイドが承認済み

バッジ: 8

+5 個以上のバッジ

チーム

IUPUI, Team 3-1, Harley Fall 2015 IUPUI, Team 3-1, Harley Fall 2015人のメンバー

IUPUI-HARLEY-F15S3G1

4 メンバー

5のガイドは作成済み

コメント 1 件

Where can I purchase just the rumble motors? I'd like to try adding rumble to a PDP Rock Candy controller, which is essentially the same controller as the AfterGlow but in a neon colored shell and no LED lighting. I don't know if they'll actually work but it would be a fun project.

Josh Koontz - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 5

過去 30 日: 14

今までの合計 2,647