Oliver Bagel and Bun Slicer 702-N Blade Replacement

はじめに

The Oliver Bagel and Bun Slicer 702-N is a powerful tool when it comes to slicing bagels seamlessly in a fast manner. But when it comes to maintaining and replacing internal parts, it can seem daunting. The bagel slicer is composed of various individual parts where it seems impossible to even begin the process of disassembling the slicer. In addition, this is an outdated version so there isn't much support left of this product aside from digging through decades old articles.

The purpose of this guide is to help break down the process of disassembling and replacing the blade of the slicer in digestible parts so that anyone will be able to follow along the guide. The guide will include tips to encourage proper organization of parts and safety practices during disassembly. The photos will act as an essential visual aid so users can reference as they follow the guide so that they know they're following the guide correctly.

Although cut gloves aren't necessary for disassembly, we highly recommend wearing them as the blade is extremely sharp and improper usage can lead to moderate cuts. Some workplaces even require its employees to wear them as part of workplace safety. So please, keep your hands safe and put on cut gloves!

必要な工具と部品

手順1 Blade

Oliver Bagel and Bun Slicer 702-N Blade Replacement, Blade: 手順 1、 1の画像 1

Remove the black knob underneath the bagel slicer base by twisting it counterclockwise.

編集

手順2

On the left end of the slicer, repeat the previous step to remove the bottom knob.

編集

手順3

Remove the knob located in the middle by twisting it counterclockwise.
After removing the knob, smoothly pull out the lock.

編集

手順4

Locate the knob on the left and repeat Step 3 to remove the knob and lock.

編集

手順5

While holding the ends of the bagel chute, lift the entire chute up and set it aside.
When you remove the chute, the sharp blade will be exposed. Take further caution as you proceed through the guide.

編集

手順6

Oliver Bagel and Bun Slicer 702-N Blade Replacement: 手順 6、 3の画像 3

Remove all three nuts on the blade cover.
It’s important to separate and organize the different small parts in each step to ensure a smooth reassembling process.

編集

手順7

Carefully lift up the blade cover and set aside.

編集

手順8

Remove the black knobs on both sides of the blade and set aside.
Make sure that you keep these knobs separate from the knobs in Steps 1-6 as they look identical but are not interchangeable between each other.

編集

手順9

Carefully lift up the part and set aside.
Hold the part by its ends so that your hands are as far from the blade as possible.

編集

手順10

Put on cut gloves before proceeding.
Using a 7/16 wrench, remove the three bolts.
You may spin the blade clockwise to make the removal process easier.

編集

手順11

Carefully the lift the blade up and set aside in a safe spot.
Now is a great time to clean and wipe down all individual parts if needed.

編集

手順12

With a new blade, place the blade down and align the holes with the holes of the bagel slicer base.

編集

手順13

Hold the blade with your non-dominant hand to keep it steady.
Screw back in all three bolts of the blade with your by twisting it clockwise.

編集

手順14

Once the bolts are somewhat secured, use the 7/16 wrench again to tighten them until firm.

編集

手順15

Insert the part with the outward sticking bolt and place the part down.
Make sure to align the outward sticking bolt's hole with the screw.

編集

手順16

Twist the black knobs clockwise on both sides of the part until firmly tight.
Make sure you are using the same black knobs you removed in Step 10.

編集

手順17

Align the holes of the bagel cover with the bolts and place the cover down.

編集

手順18

Oliver Bagel and Bun Slicer 702-N Blade Replacement: 手順 18、 3の画像 3

Twist all three nuts on the bagel cover clockwise until tight.

編集

手順19

On the bagel chute you removed in Step 5, align the lock's hole with the bolt.
Place a black knob on top and twist clockwise until tight.

編集

手順20

Oliver Bagel and Bun Slicer 702-N Blade Replacement: 手順 20、 3の画像 3

Repeat Step 19 for the other knob.
After completing Steps 19 and 20, your bagel chute should look like the third image.

編集

手順21

Place the bagel chute on top of the metallic slicer base.
The bottom part of the lock should go underneath the base.
Line up the holes of the locks with the bolts and twist a black knob into the hole of the base.
Due to the obscure position of the bolt, you can insert the black knob into the lock first and move it back and forth until you feel a hole.