メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

Using this guide, people will be able to replace the plastic shell of their blender in case of cracks or aesthetic issues.

パーツ

パーツは指定されていません。

  1. Remove the cup from the blender base.
    • Remove the cup from the blender base.

  2. Turn the blender over and unscrew the three 14 mm screws holding the slotted base in place. These are Torx Security bits (TR9) on some units. Turn the blender over and unscrew the three 14 mm screws holding the slotted base in place. These are Torx Security bits (TR9) on some units.
    • Turn the blender over and unscrew the three 14 mm screws holding the slotted base in place. These are Torx Security bits (TR9) on some units.

  3. 今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る

    今あるものを使い続けましょう

    オールインワインキットで安く修理して、節約しましょう。

    iPhone 修理キットを見る
  4. Using a the standard Phillips head screwdriver bit, remove the slotted black plastic covering and then unscrew the one 11mm screw holding the power cord in place. Unscrew the four 14 mm screws that are in the deep slots.  This will release the motor from the base. Unscrew the four 14 mm screws that are in the deep slots.  This will release the motor from the base.
    • Using a the standard Phillips head screwdriver bit, remove the slotted black plastic covering and then unscrew the one 11mm screw holding the power cord in place.

    • Unscrew the four 14 mm screws that are in the deep slots. This will release the motor from the base.

  5. CAUTION: the silver blade attached to the motor is very sharp.  Use a towel or thick cloth to protect your hands for the next step. Using a towel, hold the silver fan still.  Twist the small black rubber wheel that is attached to the top of the blender base to the right.  This will remove the wheel for replacement. Using a towel, hold the silver fan still.  Twist the small black rubber wheel that is attached to the top of the blender base to the right.  This will remove the wheel for replacement.
    • CAUTION: the silver blade attached to the motor is very sharp. Use a towel or thick cloth to protect your hands for the next step.

    • Using a towel, hold the silver fan still. Twist the small black rubber wheel that is attached to the top of the blender base to the right. This will remove the wheel for replacement.

  6. Use the standard Phillips head screw bit to unscrew the screws in the black plastic with the silver circular discs. Using the T9 screw bit, unscrew the four sets of two 11 mm screws located on each of the four sides of the motor. Using the T9 screw bit, unscrew the four sets of two 11 mm screws located on each of the four sides of the motor.
    • Use the standard Phillips head screw bit to unscrew the screws in the black plastic with the silver circular discs.

    • Using the T9 screw bit, unscrew the four sets of two 11 mm screws located on each of the four sides of the motor.

  7. Untwist the small rubber connector to detach the plastic from the motor. Untwist the small rubber connector to detach the plastic from the motor.
    • Untwist the small rubber connector to detach the plastic from the motor.

終わりに

To reassemble your device, follow these instructions in reverse order.

Morgan Blauth

メンバー登録日: 2016年02月24日

714 ポイント

5のガイドは作成済み

チーム

USF Tampa, Team 1-5, Leahy Spring 2016 USF Tampa, Team 1-5, Leahy Spring 2016人のメンバー

USFT-LEAHY-S16S1G5

2 メンバー

5のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 3

過去 7 日: 5

過去 30 日: 34

今までの合計 1,754