はじめに

Gather tools needed. Have a small tray or container on hand to hold screws and cell phone parts as you disassemble and reassemble the Nokia 6061.

Gather the necessary tools: T6 Torx screwdriver Plastic opening tool
  • Gather the necessary tools:

  • T6 Torx screwdriver

  • Plastic opening tool

  • Small flathead screwdriver

コメントを追加する

This guide will show you how to replace the LCD—after it's been dropped one too many times.
  • This guide will show you how to replace the LCD—after it's been dropped one too many times.

コメントを追加する

Using a 2.0 flathead screwdriver, pry open and remove the black, plastic strip (beneath the screen) to reveal the 2 screws holding the screen in place.
  • Using a 2.0 flathead screwdriver, pry open and remove the black, plastic strip (beneath the screen) to reveal the 2 screws holding the screen in place.

コメントを追加する

Remove the two T6 Torx screws from the base of the display.
  • Remove the two T6 Torx screws from the base of the display.

コメントを追加する

Once the screws are removed, flip the phone shut. Insert the plastic opening tool at the position indicated and pry along the seam between the front cover and display. Continue prying along the perimeter of the front cover until it is free from the phone.
  • Once the screws are removed, flip the phone shut.

  • Insert the plastic opening tool at the position indicated and pry along the seam between the front cover and display.

  • Continue prying along the perimeter of the front cover until it is free from the phone.

コメントを追加する

Use a plastic opening tool to pry the LCD circuit board up and out of the phone. Be careful not to damage the circuit board.
  • Use a plastic opening tool to pry the LCD circuit board up and out of the phone.

  • Be careful not to damage the circuit board.

  • Flip the display up and over to expose its ribbon cable connector.

コメントを追加する

Use a plastic opening tool to gently pry the LCD ribbon cable connector up out its socket on the LCD circuit board. The other two photos show the male and female sides of the small green connector. Make sure they snap together tightly when the new display is attached. The other two photos show the male and female sides of the small green connector. Make sure they snap together tightly when the new display is attached.
  • Use a plastic opening tool to gently pry the LCD ribbon cable connector up out its socket on the LCD circuit board.

  • The other two photos show the male and female sides of the small green connector. Make sure they snap together tightly when the new display is attached.

コメントを追加する

To reassemble your phone, reattach the display to the phone by reconnecting the display ribbon cable. Place the screen assembly back into the front case of the phone.
  • To reassemble your phone, reattach the display to the phone by reconnecting the display ribbon cable. Place the screen assembly back into the front case of the phone.

コメントを追加する

Replace the phone cover by applying pressure until a click is heard.
  • Replace the phone cover by applying pressure until a click is heard.

コメントを追加する

With the cover reattached, flip the phone into the open position and replace the screws removed in step 3.  The screw-holes are indicated in the photo.
  • With the cover reattached, flip the phone into the open position and replace the screws removed in step 3. The screw-holes are indicated in the photo.

  • Replace the black, plastic strip by applying pressure until the strip audibly clicks into place.

コメントを追加する

ゴール

rosin7

メンバー登録日: 2013年02月14日

55 ポイント

4のガイドは作成済み

チーム

Ohio State, Team 1-3, Buehl Spring 2013 Ohio State, Team 1-3, Buehl Spring 2013人のメンバー

OSU-BUEHL-S13S1G3

4 メンバー

4のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 3

今までの合計 736