はじめに

After you have successfully completed the faceplate and circuit board removal guide this guide will show you how to replace the speaker

Place your thumb on the middle of the back cover and push it toward the bottom of the phone to slide the cover off. Place your thumb on the middle of the back cover and push it toward the bottom of the phone to slide the cover off. Place your thumb on the middle of the back cover and push it toward the bottom of the phone to slide the cover off.
  • Place your thumb on the middle of the back cover and push it toward the bottom of the phone to slide the cover off.

コメントを追加する

Use a plastic opening tool (or your finger) to gently pry the battery out of the battery slot on the back of the phone. Use a plastic opening tool (or your finger) to gently pry the battery out of the battery slot on the back of the phone. Use a plastic opening tool (or your finger) to gently pry the battery out of the battery slot on the back of the phone.
  • Use a plastic opening tool (or your finger) to gently pry the battery out of the battery slot on the back of the phone.

コメントを追加する

Lift the metal sim card holder (at the bottom of the battery slot) up and carefully pry the sim card out of its slot with a plastic opening tool or your finger. After removal, lower the metal sim card holder into its original position. After removal, lower the metal sim card holder into its original position.
  • Lift the metal sim card holder (at the bottom of the battery slot) up and carefully pry the sim card out of its slot with a plastic opening tool or your finger.

  • After removal, lower the metal sim card holder into its original position.

コメントを追加する

Insert the plastic opening tool into the crack between the front and back panels. Gently pry the front cover away from the back cover while sliding the plastic opening tool towards the top of the phone.
  • Insert the plastic opening tool into the crack between the front and back panels.

  • Gently pry the front cover away from the back cover while sliding the plastic opening tool towards the top of the phone.

コメントを追加する

Lift the bottom of the front cover away from the phone. Continue lifting until the top of the front cover is fully removed from the phone.
  • Lift the bottom of the front cover away from the phone.

  • Continue lifting until the top of the front cover is fully removed from the phone.

  • Note: To replace the Keypad, gently lift it out of the front cover. It is located below the clear viewing window.

コメントを追加する

Use the Torx screwdriver with the T6 attachmet  to remove the 6 .4 mm screws around the outside of the circuit board.
  • Use the Torx screwdriver with the T6 attachmet to remove the 6 .4 mm screws around the outside of the circuit board.

  • Note: Removing the 4 T6 screws around the screen will loosen it, so don't worry if the screen also separates from the circuit board.

コメントを追加する

Lift the circuit board out of the back cover. Lift the circuit board out of the back cover. Lift the circuit board out of the back cover.
  • Lift the circuit board out of the back cover.

コメントを追加する

Using the plastic opening tool, gently pry the speaker out of its slot in the back cover of the phone. Note: The easiest way to remove the speaker is to insert the plastic opening tool in the upper right corner of the speaker. Note: The easiest way to remove the speaker is to insert the plastic opening tool in the upper right corner of the speaker.
  • Using the plastic opening tool, gently pry the speaker out of its slot in the back cover of the phone.

  • Note: The easiest way to remove the speaker is to insert the plastic opening tool in the upper right corner of the speaker.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Taylor Hinsdale

メンバー登録日: 2010年10月05日

84 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 7-52, Amido Fall 2010 Cal Poly, Team 7-52, Amido Fall 2010人のメンバー

CPSU-AMIDO-F10S7G52

4 メンバー

12のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 1

過去 30 日: 5

今までの合計 2,437