はじめに

Use this guide to remove the plastic stylus housing from your DSi.

Unscrew the two Phillips screws securing the battery cover to the lower case. The screws remain captive to the battery cover.
  • Unscrew the two Phillips screws securing the battery cover to the lower case.

  • The screws remain captive to the battery cover.

  • Grasp the battery cover and lift out of the lower case.

コメントを追加する

Wedge the edge of a spudger in between the top of the battery and its lower case housing and pry upwards to dislodge the battery. Grasp the battery and remove it from the DSi.
  • Wedge the edge of a spudger in between the top of the battery and its lower case housing and pry upwards to dislodge the battery.

  • Grasp the battery and remove it from the DSi.

コメントを追加する

Two screws are hidden underneath two rubber feet highlighted in red. Use the tip of a spudger to pry the rubber feet out of the lower case.
  • Two screws are hidden underneath two rubber feet highlighted in red.

  • Use the tip of a spudger to pry the rubber feet out of the lower case.

One of the feet did break on me, tweezers came in handy for picking it out

Willie Narvaez - 返信

Remove the following screws securing the lower case to the body of the DSi:
  • Remove the following screws securing the lower case to the body of the DSi:

    • Six 5.2 mm Phillips screws.

    • One 2.7 mm Phillips screw.

コメントを追加する

Insert the spudger in between the lower casing and lower panel near the top right corner of the DSi. Carefully run the spudger along the edge of the outer casing, creating an opening between the body and the casing. Continue running the spudger around the body of the DSi until the majority of the lower case has been separated.
  • Insert the spudger in between the lower casing and lower panel near the top right corner of the DSi.

  • Carefully run the spudger along the edge of the outer casing, creating an opening between the body and the casing.

  • Continue running the spudger around the body of the DSi until the majority of the lower case has been separated.

コメントを追加する

Carefully lift the lower casing from its bottom edge. The lower case is still attached to the motherboard by the volume and SD board cable highlighted in red. Do not try to completely remove the lower case of the DSi yet.
  • Carefully lift the lower casing from its bottom edge.

  • The lower case is still attached to the motherboard by the volume and SD board cable highlighted in red. Do not try to completely remove the lower case of the DSi yet.

  • Pry the volume and SD board cable up from its socket on the motherboard with the flat edge of a screwdriver.

  • once the cable, highlighted in the orange box, is completely removed then you may take off the entire outer casing.

コメントを追加する

Pull the stylus straight out its housing and remove it from the rear case.
  • Pull the stylus straight out its housing and remove it from the rear case.

コメントを追加する

Remove the five 3.9 mm Phillips screws securing the stylus holder to the rear case.
  • Remove the five 3.9 mm Phillips screws securing the stylus holder to the rear case.

コメントを追加する

Lift and remove the left plastic protector from the DSi's rear case. Grasp the stylus holder from the left side and lift upwards to remove it from the DSi.
  • Lift and remove the left plastic protector from the DSi's rear case.

  • Grasp the stylus holder from the left side and lift upwards to remove it from the DSi.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

Walter Galan

556,664 ポイント

2,885のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 14

今までの合計 5,199