メニュー

あなたの設定

私のワークベンチ

お持ちのデバイス用の修理ガイド、交換用パーツやアンサーフォーラムにアクセスする。
カート

カートには何も入っていません。

当社のショップを閲覧する

Nintendo 64 Motherboard Replacement

おすすめ

作成者： tonymag28 (そして 11 人のその他投稿者)
  • コメント: 2
  • お気に入り: 40
  • 完了: 24

おすすめのガイド

難易度

簡単

手順

16

所要時間

15 - 20 分

セクション

3

フラグ

1

Featured Guide

おすすめのガイド

このガイドはiFixitスタッフによって太鼓判が押されています。

はじめに

This guide will show how to replace the Nintendo 64 motherboard.

ツール

これらのツールを購入する

パーツ

パーツは必要ありません。

  1. Remove the expansion pack cover by pushing in the tab and pulling out.

    • Remove the expansion pack cover by pushing in the tab and pulling out.

    編集

  2. If your system uses a jumper pack, the same procedure applies to remove it.

    • If your system uses a jumper pack, the same procedure applies to remove it.

    • A small spoon can be used in place of a spudger.

    • Lever the expansion pack out using a metal spudger.

    編集

  3. Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    • Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    編集

  4. Remove the two front feet of the N64.

    • Remove the two front feet of the N64.

    編集

  5. Rotate to top side up and lift off top cover.

    • Rotate to top side up and lift off top cover.

    編集

  6. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    • Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    編集

  7. Pro Tech ツールキットを含むご注文、もしくは総額 $100ドル以上のご注文については送料無料です。

    当社のショップを閲覧する

  8. Remove the metal plate indicated in the example by sliding it back and then lifting it up. Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    • Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    編集

  9. Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    • Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    編集

  10. Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    • Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    編集

  11. Remove the small metal bracket from the back of the expansion pack slot.

    • Remove the small metal bracket from the back of the expansion pack slot.

    編集

  12. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    • Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    編集

  13. Remove the small metal bracket behind the expansion slot using the spudger. Remove the small metal bracket behind the expansion slot using the spudger.

    • Remove the small metal bracket behind the expansion slot using the spudger.

    編集

  14. Remove the seven screws indicated in the example using the larger Phillips screwdriver. Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    • Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    編集

  15. Lift off and remove the metal plate as indicated in the example.

    • Lift off and remove the metal plate as indicated in the example.

    編集

  16. Remove the four screws indicated using the #1 Phillips screwdriver.

    • Remove the four screws indicated using the #1 Phillips screwdriver.

    編集

  17. Lift up and remove the motherboard.

    • Lift up and remove the motherboard.

    編集
まとめ

To reassemble your device, follow these instructions in reverse order.

24 の人々がこのガイドを完成させました。

作成者

11他の投稿者と一緒に

tonymag28

メンバー登録日: 2009年10月28日

1,664 ポイント

3のガイドは作成済み

バッジ: 13

+10 個以上のバッジ

チーム

Cal Poly, Team 5-4, Regan Fall 2009 Cal Poly, Team 5-4, Regan Fall 2009人のメンバー

CPSU-REGAN-F09S5G4

7 メンバー

6のガイドは作成済み

コメント1件

コメントを追加

4.2mm doesn't seem right. When I looked to purchase all I saw was 4.5mm and now that I have one in my hand it seems to fit very precisely on the screws on my N64.

negroslim - 返信

コメントを追加する

1024

統計データを表示:

過去 24時間: 9

過去 7 日: 36

過去 30 日: 212

今までの合計 46,342