はじめに

This guide shows how to remove the metal plate that covers the motherboard.

Remove the expansion pack cover by pushing in the tab and pulling out.
  • Remove the expansion pack cover by pushing in the tab and pulling out.

コメントを追加する

Lever the expansion pack out using the metal spudger.
  • Lever the expansion pack out using the metal spudger.

  • A small spoon can be used in place of a spudger.

コメントを追加する

Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.
  • Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

コメントを追加する

Remove the two front feet of the N64.
  • Remove the two front feet of the N64.

コメントを追加する

Rotate to top side up and lift off top cover.
  • Rotate to top side up and lift off top cover.

コメントを追加する

MacBook Battery Fix Kits
Fix Kits Starting at $69.99
MacBook Battery Fix Kits
Starting at $69.99
Remove the fourteen screws indicated in the example using the larger Phillips screwdriver. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.
  • Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

I’m not entirely certain if it's a common difference, but my nintendo 64 doesn’t have fourteen screws, but rather, 8 screws, and instead of 3 heat sinks, it only has the one separate heat sink on the chip close to the memory expansion pack. additionally, aside from the 6 screws closest to the expansion pack, the two other screws are held on by nuts under the metal piece.

Avery Duncan - 返信

Remove the metal plate indicated in the example by sliding it back and then lifting it up. Remove the metal plate indicated in the example by sliding it back and then lifting it up.
  • Remove the metal plate indicated in the example by sliding it back and then lifting it up.

コメントを追加する

Remove the two screws indicated in the example using the smaller Phillips screwdriver.
  • Remove the two screws indicated in the example using the smaller Phillips screwdriver.

コメントを追加する

Remove the screw to the right of the LED light using the larger Phillips screwdriver.
  • Remove the screw to the right of the LED light using the larger Phillips screwdriver.

コメントを追加する

Remove the small metal bracket from the back of the expansion pack slot.
  • Remove the small metal bracket from the back of the expansion pack slot.

コメントを追加する

Remove the small metal bracket from the front of the expansion pack slot with the metal spudger. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.
  • Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

コメントを追加する

Remove the small metal bracket behind the expansion slot using the spudger. Remove the small metal bracket behind the expansion slot using the spudger.
  • Remove the small metal bracket behind the expansion slot using the spudger.

コメントを追加する

Remove the seven screws indicated in the example using the larger Phillips screwdriver. Remove the seven screws indicated in the example using the larger Phillips screwdriver.
  • Remove the seven screws indicated in the example using the larger Phillips screwdriver.

コメントを追加する

Lift off and remove the metal plate as indicated in the example.
  • Lift off and remove the metal plate as indicated in the example.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

LisaF818

メンバー登録日: 2009年11月29日

95 ポイント

1ガイドが承認済み

チーム

Cal Poly, Team 5-4, Regan Fall 2009 Cal Poly, Team 5-4, Regan Fall 2009人のメンバー

CPSU-REGAN-F09S5G4

7 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 6

過去 30 日: 31

今までの合計 8,587