メインコンテンツにスキップ

Nintendo 2DS Joystickの交換

必要な工具と部品

  1. Nintendo 2DS Joystickの交換, バッテリー: 手順 1、 1の画像 1
    • 上の後面パネルを固定しているプラス(脱落防止)ネジを2本外します。

    • (脱落防止)ネジはバックパネルから完全に外れません。

  2. Nintendo 2DS Joystickの交換: 手順 2、 2の画像 1 Nintendo 2DS Joystickの交換: 手順 2、 2の画像 2
    • 上部リアパネルを上方および外側に持ち上げて、ヒンジから取り外します。

  3. Nintendo 2DS Joystickの交換: 手順 3、 3の画像 1 Nintendo 2DS Joystickの交換: 手順 3、 3の画像 2 Nintendo 2DS Joystickの交換: 手順 3、 3の画像 3
    • 外側のエッジに一番近い側からバッテリー筐体を持ち上げて、バッテリーを取り出します。

  4. Nintendo 2DS Joystickの交換, リアパネル: 手順 4、 1の画像 1
    • リアパネルに留められたプラスネジを10本外します。

    Can't take off the screw top left next to the battery. What type of screwdriver do I use and where can I find some?

    Little Mac - 返信

    I used a husky with changeable heads, you could probably find one on amazon

    Minecrafter Pig -

  5. Nintendo 2DS Joystickの交換: 手順 5、 1の画像 1
    • 後面パネルはリボンケーブルでマザーボードと接続されているので、デバイスから持ち上げるときは離れすぎないように気を付けてください。

    • デバイスから後面パネルを慎重に垂直に引き上げます。

  6. Nintendo 2DS Joystickの交換: 手順 6、 1の画像 1
    • 接続しているリボンケーブルの位置を見つけるために、バックパネルを慎重に裏返します。

    • リアパネルとリボンケーブルを繋いでいるプラスネジを2本外します。

    • ここで、左右のトリガーを取り出すこともできます。このトリガーにはヒンジが付いています。バネが取り出したり、ヒンジを破損することもありますのでご注意ください。

    You can also detach the cable from the motherboard safely by flipping up the connector on the motherboard. Just don't forget to reattach. Some will find this tedious but may save time if you know what you're doing with said connectors.

    Blackbeard - 返信

    I agree, this is what the guide i followed said to do and since I was disconnecting all the other ribbon cables it made perfect sense to do it that way.

    Lin -

    pay attention: my 2ds dropped it's lens covers at this step

    Jos van Reenen - 返信

    Likewise, I used a tiny drop of glue to put the lens back in place. Take care not to dirty the lens.

    Elliot West -

    The picture you have there has the camera lens ribbon installed upside down. The ribbon needs to be pointing down when you re-attach it not up.

    Rick Parrish - 返信

    Agreed, ribbon cable looks upside down in picture

    Elliot West -

  7. Nintendo 2DS Joystickの交換, Joystick: 手順 7、 2の画像 1 Nintendo 2DS Joystickの交換, Joystick: 手順 7、 2の画像 2
    • トリガーボタンを上向きと外側に引っ張り、右上コーナーから取り出します。

    • 赤の右側サイドパネルを外側に引いて、取り出します。

    I recommend not removing the right trigger. I didn’t find it necessary and I hard a hard time getting the spring lined up again.

    Tyler Schommer - 返信

  8. Nintendo 2DS Joystickの交換: 手順 8、 1の画像 1
    • JoystickリボンケーブルのZIFコネクタ上に付いているグレーの固定レバーを、スパッジャーで持ち上げます。ケーブルと反対側のコネクタ上にあるマザーボードからまっすぐ持ち上げます。

    • 慎重にケーブルをコネクタからスライドして、外します。

  9. Nintendo 2DS Joystickの交換: 手順 9、 1の画像 1
    • 白いJoystickカバーを固定している2本のプラスネジを外します。

  10. Nintendo 2DS Joystickの交換: 手順 10、 2の画像 1 Nintendo 2DS Joystickの交換: 手順 10、 2の画像 2
    • Joystickカバーを取り出します。

    • Joystickカバーの下にあるワッシャーを取り出します。

    I completed the tutorial but my stick is now drifting by itself and I’m afraid to open it up again and try because the screws, it seems, are damaged from scratching it too much. It’s been like that for at least a year

    ImTHATGuy 500 - 返信

終わりに

デバイスを再組立する際は、これらのインストラクションを逆の順番に従って作業を進めてください。

20 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

en jp

100%

Midori Doiさんは世界中で修理する私たちを助けてくれています! あなたも貢献してみませんか?
翻訳を始める ›

作成者

4人の作成者と共同で作成されました。

Fina Beauchamp

メンバー登録日: 01/12/15

2,982 ポイント

6のガイドは作成済み

チーム

Cal Poly, Team 70-1, Forte Winter 2015 Cal Poly, Team 70-1, Forte Winter 2015人のメンバー

CPSU-FORTE-W15S70G1

4 メンバー

35のガイドは作成済み

12 件のコメント

My ribbon cable is broke, Is there a way to fix it?Thanks.

Deez Smith - 返信

When I put the circle pad back in, my 2DS thinks that I am holding up and right on it, when in reality it is in the neutral position. Please help.

CraftedGamer 1170 - 返信

Use the calibrate option in system settings. Also make sure the cable is connected nicely.

Jilvenhong Dickinson -

Recalibrate it in system settings.

Artemy Matveev - 返信

The guide fails to mention that the joystick ribbon cable is locked into the motherboard. You can use a spudger to lift the grey tab, leveraging upwards on the side opposite of the ribbon cable. The tab will pop up and should make getting the ribbon cable out (and back in) easier.

I followed this guide and ripped the ribbon cable while attempting to get it connected back to the system. If I had known the grey tab unlocks, I might not have ripped the cable by trying to force it back under the pins. My iFixit tweezers were also very sharp, and may have cut the ribbon cable. Would anyone be able to recommend something gentler for the ribbon cable?

Ryan G - 返信

@ryango This looks like an oversight on the part of the guide author. I’ve updated the text with (hopefully) better instructions. Sorry it led to tearing your cable. :( That looks like a pretty standard ZIF connector, and once unlocked, it should disconnect and reconnect with minimal force. Personally when working with ribbon cables I prefer blunt-nose tweezers, but it sounds like your tweezers weren’t at fault here. Thanks for the heads-up, and better luck with your next repair.

Jeff Suovanen -

I replaced my analog stick, but it has the same problem, when i turn on the system, the cursor go crazy and then stops, i can move only left and right, no up and down with two different analog sticks…so, it’s not a analog problem, do u have any idea on how to fix it? thank you

Emiliano Tricase - 返信

Try recalibrating it, I guess. After that, let me know how it is? I might find another possible solution.

INFJ Blog -

A bit nervous to try this, do I have to detach the ribbon cables?

INFJ Blog - 返信

So mine doesn't have the gray tab. Any help with that?

jeff why not? - 返信

I've found that a Phillips #000 Screwdriver works better.

Raymond Trinh - 返信

Will iFixit be selling the parts for this repair ever again?

Noboru Garcia - 返信

コメントを追加

統計データ:

過去 24時間: 10

過去 7 日: 94

過去 30 日: 415

今までの合計 28,968