はじめに

Tubing is prone to leaking and replacing the hot water tubing may eliminate any problems you may be facing with your device or prevent problems down the road. Replacing the main hot water tube involves removing screws on both the top and bottom panel, so it may be a good idea to use the iFixit magnetic pad to keep track of loose screws.

  1. Unscrew (8) 6mm screws using Phillips head #1 screwdriver Remove bottom cover
    • Unscrew (8) 6mm screws using Phillips head #1 screwdriver

    • Remove bottom cover

  2. Unscrew (3) 6mm screws with Phillips head #1 screwdriver
    • Unscrew (3) 6mm screws with Phillips head #1 screwdriver

    • Remove tube protection plate

  3. Detach valve tubes from valve by squeezing pins and pull tubes away from valve
    • Detach valve tubes from valve by squeezing pins and pull tubes away from valve

  4. Detach valve tubes from device by pinching pins and sliding the tubes off
    • Detach valve tubes from device by pinching pins and sliding the tubes off

  5. Free shipping on all orders over $100 or containing a Pro Tech Toolkit!

    当社のショップを閲覧する
  6. Unscrew the four 6mm #1 Phillips head screws from the underside of the basket area. Remove the single 6mm #1 Phillips-head screw from the side of the unit.
    • Unscrew the four 6mm #1 Phillips head screws from the underside of the basket area.

    • Remove the single 6mm #1 Phillips-head screw from the side of the unit.

  7. Slowly pry the upper cover away from the unit on top of the brew basket, and near the base of the water reservoir along the side of the upper cover. Slowly pry the upper cover away from the unit on top of the brew basket, and near the base of the water reservoir along the side of the upper cover.
    • Slowly pry the upper cover away from the unit on top of the brew basket, and near the base of the water reservoir along the side of the upper cover.

  8. Separate hose from upper nozzle by squeezing the clamp and pulling the hose down slightly.
    • Separate hose from upper nozzle by squeezing the clamp and pulling the hose down slightly.

  9. Using a #1 Phillips head screwdriver with an extension, remove three 6mm screws  holding the heater to the unit. Using a #1 Phillips head screwdriver with an extension, remove three 6mm screws  holding the heater to the unit.
    • Using a #1 Phillips head screwdriver with an extension, remove three 6mm screws holding the heater to the unit.

  10. Remove heater from unit.
    • Remove heater from unit.

  11. Squeeze clip and separate signal wiring. Using wire stripper/crimping tool, uncrimp wiring connectors
    • Squeeze clip and separate signal wiring.

    • Using wire stripper/crimping tool, uncrimp wiring connectors

    • Wiring connectors are sealed together making them difficult to disconnect. Cutting and rewiring should be considered.

  12. Squeeze connector and pull tubing away from heater.
    • Squeeze connector and pull tubing away from heater.

    • Inspect tubing for damage and/or weak spots and replace if necessary.

まとめ

To reassemble your device, follow these instructions in reverse order.

Kyle Gustafson

メンバー登録日: 2018年11月04日

79 ポイント

1ガイドが承認済み

チーム

UMass Dartmouth, Team S5-G4, Gulbrandsen Fall 2018 UMass Dartmouth, Team S5-G4, Gulbrandsen Fall 2018人のメンバー

UMASSD-GULBRANDSEN-F18S5G4

3 メンバー

5のガイドは作成済み

統計データを表示:

過去 24時間: 2

過去 7 日: 3

過去 30 日: 19

今までの合計 108