はじめに

Use this guide to remove the circuit board that activates the automatic firing mechanism.

Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.
  • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

  • Remove the two 9.0 mm Phillips screws securing the battery compartment.

  • Slide the battery compartment out.

コメントを追加する

Remove the five 9.0 mm Phillips screws securing the trigger.
  • Remove the five 9.0 mm Phillips screws securing the trigger.

コメントを追加する

  • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

  • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

コメントを追加する

  • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

  • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

コメントを追加する

  • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

コメントを追加する

  • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

コメントを追加する

  • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

  • Remove the single 7.0 mm Phillips screw below the barrel.

  • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

コメントを追加する

  • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

コメントを追加する

  • Remove the two 9.0 mm Phillips screws holding together the handle.

  • Remove the plastic cover of the handle.

コメントを追加する

  • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

  • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

コメントを追加する

  • Pull one end of the handle away from the orange latch.

  • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

コメントを追加する

  • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

  • Completely remove the left shell from the rest of the Nerf Gun.

コメントを追加する

  • Remove the cartridge support.

コメントを追加する

  • Remove the handle crank.

コメントを追加する

  • Remove the clear plastic barrel cover.

コメントを追加する

  • Remove the firing pin.

コメントを追加する

  • Lift the trigger mechanism out of the shell.

  • You cannot fully remove the trigger mechanism just yet. However taking it out of the shell helps in later steps.

コメントを追加する

  • Remove the two 9.0 mm Phillips screws.

コメントを追加する

  • To remove the motor and trigger mechanism you have to detach these two wires which are glued to the shell.

  • Hold close to the wire and pull upward slowly.

  • If you pull too quickly you can potentially damage the wire.

コメントを追加する

  • Once all the pieces are removed the right shell should be fully accessible.

コメントを追加する

  • Once you have the handle disassembled locate the triggering circuit board.

コメントを追加する

  • Find the two plastic clasps and position your hands so you can pry them open with your fingers. We recommend that you try and pry them open without removing the piece so you can feel how fragile the plastic is.

コメントを追加する

  • The circuit board has sharp metal solder points on it. If your finger slips you could injure yourself. Consider using gloves.

  • To remove use two fingers to pry the plastic edges apart and with your thumbs remove the circuit board. Having a friend help with this step could be beneficial.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

sage

メンバー登録日: 2014年01月24日

301 ポイント

3のガイドは作成済み

チーム

Cal Poly, Team 13-13, Regan Winter 2014 Cal Poly, Team 13-13, Regan Winter 2014人のメンバー

CPSU-REGAN-W14S13G13

4 メンバー

7のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 6

今までの合計 725