Neato Botvac D75 LCD Screen Replacement

はじめに

Removing and replacing the LCD screen on your Botvac requires the removal of a couple of other components in order to gain access to it. Included in this guide are instructions on how to remove the battery and brushes. Make sure to keep these components organized in your removal process to ensure an easy re-assembly process.

Also, please note that there may be dirt and debris that are knocked lose while disassembling your Botvac. Keeping a clean work area will prevent you from losing parts in the mess.

必要な工具と部品

手順1 Battery

Neato Botvac D75 LCD Screen Replacement, Battery: 手順 1、 3の画像 1

Neato Botvac D75 LCD Screen Replacement, Battery: 手順 1、 3の画像 2

Neato Botvac D75 LCD Screen Replacement, Battery: 手順 1、 3の画像 3

Use Phillips #1 screwdriver to unscrew the two bottom cover screws
Be careful, the screws are self-retained on the cover itself and does not come off the battery cover.

編集

手順2

Neato Botvac D75 LCD Screen Replacement: 手順 2、 3の画像 3

Lift battery cover out.

編集

手順3

Neato Botvac D75 LCD Screen Replacement: 手順 3、 3の画像 3

Be careful when taking out the battery. Do not pull on the wires or battery trying to get the connector out.
The cord has prongs on it that are a little difficult to get out. Use a flathead screwdriver to press the release tab on the connector to remove it.

編集

手順4 Brushes

Neato Botvac D75 LCD Screen Replacement, Brushes: 手順 4、 3の画像 1

Neato Botvac D75 LCD Screen Replacement, Brushes: 手順 4、 3の画像 2

Neato Botvac D75 LCD Screen Replacement, Brushes: 手順 4、 3の画像 3

To remove the rotary brush simply grasp it firmly and pull it off.

編集

手順5

Neato Botvac D75 LCD Screen Replacement: 手順 5、 3の画像 3

Once you have everything out get the plastic opening tool and pry open the large black plastic piece.
With a little force it should come out.
The boxes show you were the clips are that hold this piece

編集

手順6

Once the black piece has been taken out, the brush just comes out easily.

編集

手順7 LCD Screen

Neato Botvac D75 LCD Screen Replacement, LCD Screen: 手順 7、 2の画像 1

Neato Botvac D75 LCD Screen Replacement, LCD Screen: 手順 7、 2の画像 2

Firmly grasp the back cover and pull away from the Botvac one side at a time.
Removing the cover will expose two 1.3mm T10 screws that must be removed to separate the cover halves.

編集

手順8

Remove these two 13mm T10 screws. You will need to use the extension in your tool set since they are deep in the casting.

編集

手順9

Eight 13mm T10 screws on the underside of the Botvac hold the casing together. These screws are not self-retained so make sure that you don’t lose them in the disassembly process.

編集

手順10

Neato Botvac D75 LCD Screen Replacement: 手順 10、 3の画像 3

The screws pictured here on either side of the Botvac require the extension in your tool set to be removed.

編集

手順11

On the back of the Botvac there are two retaining tabs that must be pressed to be released.
With the tabs released the top and bottom cover halves can be separated.

編集

手順12

Neato Botvac D75 LCD Screen Replacement: 手順 12、 3の画像 3

Carefully lift the top cover of the Botvac. On the right side of the Botvac is where you'll find the LCD screen connector to the motherboard. Carefully pull on the connector to disconnect it from the motherboard.

編集