はじめに

The metal receiver on the motherboard may need to be removed if electrical components below the plate need to be accessed, or if the metal plate itself needs to be replaced.

Locate the single 1 cm screw on the back of the device (enclosed by a red circle in the image). Using a screwdriver with a Torx 10 hex screw, begin removing the 1cm screw by turning the screwdriver counterclockwise. Remove the screw and set aside.
  • Locate the single 1 cm screw on the back of the device (enclosed by a red circle in the image).

  • Using a screwdriver with a Torx 10 hex screw, begin removing the 1cm screw by turning the screwdriver counterclockwise.

  • Remove the screw and set aside.

コメントを追加する

Rotate your device 90 degrees to the right so that the bottom of the device is facing you. Locate the two horizontal slots on the bottom of the device. You may need to remove the sticker on the bottom of the device to access these slots.
  • Rotate your device 90 degrees to the right so that the bottom of the device is facing you.

  • Locate the two horizontal slots on the bottom of the device.

  • You may need to remove the sticker on the bottom of the device to access these slots.

  • Insert the back end of the forceps into one of these slots. You may also use any other flat, narrow tool that fits into the slots.

  • Gently push the forceps into device. You should feel movement or hear a click, signifying this side of the device is unlocked.

  • Repeat with the other slot to completely unlock the device.

コメントを追加する

Grab the top and the bottom of the device and gently pull the device open. Continue pulling until you have completely removed the top cover of the device. When reassembling your device, make sure the standby key is properly in place. See the Standby Key Guide for more information.
  • Grab the top and the bottom of the device and gently pull the device open.

  • Continue pulling until you have completely removed the top cover of the device.

  • When reassembling your device, make sure the standby key is properly in place. See the Standby Key Guide for more information.

  • Also ensure that when you close the two sides of the cover the LED indicator lights are inside the information panel.

コメントを追加する

After opening the router, grab the upper left corner of the sliver face plate and gently pull the motherboard out of the slot from within the case. After opening the router, grab the upper left corner of the sliver face plate and gently pull the motherboard out of the slot from within the case.
  • After opening the router, grab the upper left corner of the sliver face plate and gently pull the motherboard out of the slot from within the case.

コメントを追加する

Slowly lift the motherboard out of the case. Slowly lift the motherboard out of the case. Slowly lift the motherboard out of the case.
  • Slowly lift the motherboard out of the case.

コメントを追加する

Holding the motherboard by the metal face plate, position the flat end of a prying tool under one of the prongs of the metal square plate. Holding the motherboard by the metal face plate, position the flat end of a prying tool under one of the prongs of the metal square plate.
  • Holding the motherboard by the metal face plate, position the flat end of a prying tool under one of the prongs of the metal square plate.

コメントを追加する

Slowly and evenly tilt the prying tool so that the metal plate begins to lift up. Slowly and evenly tilt the prying tool so that the metal plate begins to lift up.
  • Slowly and evenly tilt the prying tool so that the metal plate begins to lift up.

コメントを追加する

Re-position the prying tool underneath another metal prong on the metal face plate, as described in Step 1. Again, gently tilt the prying tool to lift the metal plate.
  • Re-position the prying tool underneath another metal prong on the metal face plate, as described in Step 1.

  • Again, gently tilt the prying tool to lift the metal plate.

コメントを追加する

Remove the prying tool and set aside. Using one hand, gently grab the sides of the metal plate and lift away from the motherboard. If the metal plate does not remove easily, tilt it as you lift the metal plate. If the metal plate is still attached, use the prying tool to detach more metal prongs.
  • Remove the prying tool and set aside.

  • Using one hand, gently grab the sides of the metal plate and lift away from the motherboard.

  • If the metal plate does not remove easily, tilt it as you lift the metal plate. If the metal plate is still attached, use the prying tool to detach more metal prongs.

コメントを追加する

まとめ

To replace the metal plate, position it over the metal frame and gently press it down until it clicks into place.

3 の人々がこのガイドを完成させました。

Cayce Rast

メンバー登録日: 2014年10月13日

403 ポイント

3のガイドは作成済み

チーム

Clemson, Team 1-2, Benson Fall 2014 Clemson, Team 1-2, Benson Fall 2014人のメンバー

CLEM-BENSON-F14S1G2

3 メンバー

5のガイドは作成済み

コメント1件

Buen articul, solo recordar que mi compañia me dio con un sello en calidad de prestamo al servicio que contrate :(

Max Denis - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 20

今までの合計 1,276