メインコンテンツにスキップ

Motorola RIZR Z3 Slider Replacement

必要な工具と部品

  1. Motorola RIZR Z3 Slider Replacement, Battery: 手順 1、 2の画像 1 Motorola RIZR Z3 Slider Replacement, Battery: 手順 1、 2の画像 2
    • Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.

  2. Motorola RIZR Z3 Slider Replacement: 手順 2、 2の画像 1 Motorola RIZR Z3 Slider Replacement: 手順 2、 2の画像 2
    • Tilt the battery by lifting at the exposed notch.

    • Slide the battery out of its casing.

  3. Motorola RIZR Z3 Slider Replacement, Motherboard: 手順 3、 1の画像 1
    • Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.

  4. Motorola RIZR Z3 Slider Replacement: 手順 4、 2の画像 1 Motorola RIZR Z3 Slider Replacement: 手順 4、 2の画像 2
    • Use a plastic opening tool to lift the plastic casing.

    • Pull the plastic casing directly away from the phone.

  5. Motorola RIZR Z3 Slider Replacement: 手順 5、 1の画像 1
    • Lift the black rubber loudspeaker housing up and out of the plastic casing.

  6. Motorola RIZR Z3 Slider Replacement: 手順 6、 2の画像 1 Motorola RIZR Z3 Slider Replacement: 手順 6、 2の画像 2
    • Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.

    • Caution: Remove carefully, if broken, the phone will not be able to make calls.

  7. Motorola RIZR Z3 Slider Replacement: 手順 7、 2の画像 1 Motorola RIZR Z3 Slider Replacement: 手順 7、 2の画像 2
    • Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.

    • Caution: Remove carefully, if broken, the phone will not function properly.

  8. Motorola RIZR Z3 Slider Replacement: 手順 8、 2の画像 1 Motorola RIZR Z3 Slider Replacement: 手順 8、 2の画像 2
    • Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.

    • Caution: Do this gently Unclipping too fast may cause damage to your phone.

  9. Motorola RIZR Z3 Slider Replacement, LCD: 手順 9、 1の画像 1
    • Turn the phone to the front.

    • Push the keypad out through the plastic casing.

  10. Motorola RIZR Z3 Slider Replacement: 手順 10、 1の画像 1
    • Turn the phone to the side.

    • Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.

  11. Motorola RIZR Z3 Slider Replacement: 手順 11、 1の画像 1
    • Use a T4 screwdriver to unscrew the two .15 inch screws holding the LCD to the faceplate.

  12. Motorola RIZR Z3 Slider Replacement: 手順 12、 3の画像 1 Motorola RIZR Z3 Slider Replacement: 手順 12、 3の画像 2 Motorola RIZR Z3 Slider Replacement: 手順 12、 3の画像 3
    • Use a spudger to pry the plastic screen casing partially up from the LCD unit.

    • Use the spudger to pry the ribbon cable away from its clip on the LCD unit.

    • Caution: Do this carefully, damage to this ribbon cable will cause a blank screen.

    • Pull the plastic screen casing directly away from the LCD unit.

  13. Motorola RIZR Z3 Slider Replacement: 手順 13、 2の画像 1 Motorola RIZR Z3 Slider Replacement: 手順 13、 2の画像 2
    • Use a spudger to lift the LCD partially away from the metal casing.

    • Use the spudger to pry the ribbon cable directly up from its clip on the metal casing.

    • Caution: Damage to the ribbon cable here will cause screen damage.

    • Pull the LCD completely away from the metal casing.

  14. Motorola RIZR Z3 Slider Replacement, Slider: 手順 14、 2の画像 1 Motorola RIZR Z3 Slider Replacement, Slider: 手順 14、 2の画像 2
    • Use the pointed end of a spudger to push the black peg into the larger side of the slot.

    • Push the peg through so that it is completely clear of the slot.

  15. Motorola RIZR Z3 Slider Replacement: 手順 15、 1の画像 1
    • Turn the phone around and slide the slider down its track until it is free of the casing.

    • The ribbon that fits into the rectangular slot on the slider will slip through this slot as you detach the slider.

終わりに

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

作成者

4人の作成者と共同で作成されました。

Andrew Vu

メンバー登録日: 10/07/11

35 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 5-34, Amido Fall 2011 Cal Poly, Team 5-34, Amido Fall 2011人のメンバー

CPSU-AMIDO-F11S5G34

4 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 4

今までの合計 1,267