はじめに

This guide shows you how to replace the camera as it may be damaged or malfunctioning. The removal of the camera itself is simple, but getting there can be tricky because of the motherboard. Carefully follow guide. Tools are required for this.

Slide the plastic case off of the back of the phone, exposing the battery. Slide the plastic case off of the back of the phone, exposing the battery. Slide the plastic case off of the back of the phone, exposing the battery.
  • Slide the plastic case off of the back of the phone, exposing the battery.

コメントを追加する

Pull up on the red battery release tab and pull the battery out of the phone. Pull up on the red battery release tab and pull the battery out of the phone. Pull up on the red battery release tab and pull the battery out of the phone.
  • Pull up on the red battery release tab and pull the battery out of the phone.

コメントを追加する

Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length. Be careful to not strip any screws.
  • Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length.

  • Be careful to not strip any screws.

コメントを追加する

Using a prying tool, snap off the front casing on the top and bottom of the phone. Using a prying tool, snap off the front casing on the top and bottom of the phone. Using a prying tool, snap off the front casing on the top and bottom of the phone.
  • Using a prying tool, snap off the front casing on the top and bottom of the phone.

コメントを追加する

Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length. Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.
  • Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.

コメントを追加する

Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing. Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing. Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.
  • Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.

コメントを追加する

Using tweezers, remove the white wire at the top of the phone near the camera. Using tweezers, remove the white wire at the top of the phone near the camera. Using tweezers, remove the white wire at the top of the phone near the camera.
  • Using tweezers, remove the white wire at the top of the phone near the camera.

コメントを追加する

Remove these nine screws using a T-5 torques. These screws should be 2.40 mm in length Remove these nine screws using a T-5 torques. These screws should be 2.40 mm in length
  • Remove these nine screws using a T-5 torques. These screws should be 2.40 mm in length

コメントを追加する

Using tweezers, removed the white electrical tape on the motherboard. Using tweezers, removed the white electrical tape on the motherboard.
  • Using tweezers, removed the white electrical tape on the motherboard.

コメントを追加する

Using the plastic opening tool, lift up to remove the connector. Using the plastic opening tool, lift up to remove the connector.
  • Using the plastic opening tool, lift up to remove the connector.

コメントを追加する

Using a pry tool, lift the jawbone  connector. Using a pry tool, lift the jawbone  connector.
  • Using a pry tool, lift the jawbone connector.

コメントを追加する

Using tweezers, carefully disconnect the cable connector by pulling the cable out. Using tweezers, carefully disconnect the cable connector by pulling the cable out.
  • Using tweezers, carefully disconnect the cable connector by pulling the cable out.

コメントを追加する

Use a spudger to disconnect the cable connector. Use a spudger to disconnect the cable connector. Use a spudger to disconnect the cable connector.
  • Use a spudger to disconnect the cable connector.

コメントを追加する

Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera. Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera. Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.
  • Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.

コメントを追加する

There should be jawbone connector here. However it was broken on this particular device. Lift it up using a pry tool. Using tweezers, remove cable from motherboard. Using tweezers, remove cable from motherboard.
  • There should be jawbone connector here. However it was broken on this particular device. Lift it up using a pry tool.

  • Using tweezers, remove cable from motherboard.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

Aaron Mak

メンバー登録日: 2014年10月29日

634 ポイント

4のガイドは作成済み

チーム

UMass Dartmouth, Team 4-3, Miles Fall 2014 UMass Dartmouth, Team 4-3, Miles Fall 2014人のメンバー

UMASSD-MILES-F14S4G3

3 メンバー

4のガイドは作成済み

コメント1件

how do u get it back on when it dose not come back on

brianna

Brianna Dittbrenner - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 175