はじめに

This guide will enable you to remove the antenna in a Motorola Atrix 4G.

Pry the rear cover from the back of the phone.
  • Pry the rear cover from the back of the phone.

Use the word "prying" rather than sliding. We were confused during this step.

Ben Sweeney - 返信

Insert a spudger or plastic opening tool into the small notch at the base of the battery. Lift the battery out of the phone.
  • Insert a spudger or plastic opening tool into the small notch at the base of the battery.

  • Lift the battery out of the phone.

コメントを追加する

Remove the four 5.0 mm T5 Torx screws from the corners of the phone. Remove three 5.5 mm T5 Torx screws from the back of the phone. Lift up the black rubber flap near the SD card slot.
  • Remove the four 5.0 mm T5 Torx screws from the corners of the phone.

  • Remove three 5.5 mm T5 Torx screws from the back of the phone.

  • Lift up the black rubber flap near the SD card slot.

  • Remove the single 5.5 mm T5 Torx screw beneath the flap.

  • Do not attempt to loosen the screws with too much force. These screws are small, and easily stripped.

Not a phillips head screwdriver. Indicate the appropriate tool.

Ben Sweeney - 返信

Hex head screwdriver.

Ben Sweeney - 返信

Remove the back case of the phone by gently lifting the tabs located on top of the phone near the lock button. Use the case opener or spudger in these small areas because the plastic tabs can be easily broken.
  • Remove the back case of the phone by gently lifting the tabs located on top of the phone near the lock button.

  • Use the case opener or spudger in these small areas because the plastic tabs can be easily broken.

  • Lift the tabs located on the bottom of the phone to continue removing the back cover.

Red boxes around the tabs so all can be seen clearly. Change the bullet point to red to accommodate said boxes.

rubixtriangle - 返信

Slide an opening tool between the gap from the back of the case to the front. After separating the sides, make sure there is a noticeable gap between the back case and the rest of the phone.
  • Slide an opening tool between the gap from the back of the case to the front.

  • After separating the sides, make sure there is a noticeable gap between the back case and the rest of the phone.

  • After detaching the tabs and sliding down the sides, there should be a noticeable gap between the front and back cases.

コメントを追加する

Carefully separate the back case from the rest of the phone by lifting it away from the phone.
  • Carefully separate the back case from the rest of the phone by lifting it away from the phone.

  • Do not completely remove the case from the rest of the phone. The antenna is connected to both cases.

コメントを追加する

Disconnect the antenna from its housing on the motherboard by gently lifting beneath it.
  • Disconnect the antenna from its housing on the motherboard by gently lifting beneath it.

Specify--lift beneath it near the gold metal piece located on the phone (not the back case)

Ben Sweeney - 返信

Ease the antenna from out of its guide along the side of the phone
  • Ease the antenna from out of its guide along the side of the phone

  • Once the antenna is detached, remove the back case and the antenna from the phone

  • The antenna is soldered to the back case. Do not pull with too much force.

Add picture for "easing out of the guide." Also, specify that you must unclip the guide from the phone.

Ben Sweeney - 返信

まとめ

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

Derek Walker

メンバー登録日: 2012年04月19日

282 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 9-42, Regan Spring 2012 Cal Poly, Team 9-42, Regan Spring 2012人のメンバー

CPSU-REGAN-S12S9G42

6 メンバー

7のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 13

今までの合計 4,933