メインコンテンツにスキップ

Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement

必要な工具と部品

  1. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: 手順 1、 3の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: 手順 1、 3の画像 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade Cover: 手順 1、 3の画像 3
    • Before you begin, make sure to power off and unplug the device from the outlet.

    • If the clear water pump hose is connected, remove it now.

    • Loosen the plastic knob holding the saw's cutting head in place.

    • Lower the cutting head while keeping it steady.

  2. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 2、 2の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 2、 2の画像 2
    • Unscrew the knob.

    • Remove it from the cutting head.

  3. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 3、 2の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 3、 2の画像 2
    • Loosen the plastic knob holding the blade cover in place.

  4. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 4、 3の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 4、 3の画像 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 4、 3の画像 3
    • Loosen the wing nut on the blade cover pivot shaft.

    • Remove the wing nut and accompanying washer.

  5. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 5、 2の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 5、 2の画像 2
    • Pivot the blade cover up and pull it off the shaft.

  6. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: 手順 6、 3の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: 手順 6、 3の画像 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Blade: 手順 6、 3の画像 3
    • Insert the provided spanner wrench into one of the four tightening holes on the inner flange behind the blade.

    • Use the the provided nut wrench to loosen the hex nut while providing counterforce with the spanner wrench.

  7. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 7、 2の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 7、 2の画像 2
    • Remove the hex nut.

    • Remove the outer flange.

  8. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 8、 2の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 8、 2の画像 2
    • Remove the cutting blade.

    • The blade can be sharp, so handle with care.

  9. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: 手順 9、 3の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: 手順 9、 3の画像 2 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Cutting Head: 手順 9、 3の画像 3
    • Pull the entire cutting head straight off the shaft holding it in place.

  10. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement, Bottom Cover: 手順 10、 1の画像 1
    • Remove the eight Phillips #2 screws on the underside of the cutting head.

  11. Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 11、 2の画像 1 Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement: 手順 11、 2の画像 2
    • Remove the bottom cover.

終わりに

To reassemble your device, follow these instructions in reverse order.

Carsten Frauenheim

メンバー登録日: 03/10/20

110,966 ポイント

338のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Staff

136 メンバー

16,579のガイドは作成済み

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 1

過去 30 日: 3

今までの合計 172