はじめに

If you need to replace the back panel of the Minimove boombox, follow the steps from this guide. This guide will involve moderate disassembly of the device, including the removal of the back covering and base.

  1. Remove the two plastic screw covers on the back of your Minimove by inserting the flat end of your plastic opening tool between the screw cover and the back panel and prying it out.
    • Remove the two plastic screw covers on the back of your Minimove by inserting the flat end of your plastic opening tool between the screw cover and the back panel and prying it out.

    • It may be helpful to pull the plastic covers out with your fingers once the top of the cover has been revealed by using the plastic opening tool.

    コメントを追加する

  2. This step will require at least a 30 mm Phillips #1 screwdriver.
    • This step will require at least a 30 mm Phillips #1 screwdriver.

    • Use a Phillips #1 screwdriver to remove the two 12 mm screws.

    コメントを追加する

    • The bottom panel screws and screw covers must be removed in order to access the back panel.

    • Remove the four grey screw covers by inserting the plastic opening tool underneath the screw covers and rotating around the circumference.

    • The adhesive on the screw covers should be sticky enough to put the covers back on when re-assembling the device.

    コメントを追加する

    • Remove the two 8 mm screws with a Phillips #1 screwdriver.

    • Remove the two 12 mm screws with a long Phillips #1 screwdriver.

    コメントを追加する

  3. Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    • To remove the back panel, use the plastic opening tool and gently work around the outline of the panel. The outline wraps around the sides and can be spotted at the top back of the device.

    コメントを追加する

    • Be careful not to use too much force to remove the panel. The antenna wire is connected to the inside of the panel and may be damaged or ripped off if the panel is not gently removed.

    • After loosening the panel with the plastic opening tool, use moderate force to pry open the panel with your hands.

    • Carefully pull the panel off.

    コメントを追加する

    • Use a Phillips #1 screwdriver to detach the wire from the back panel by removing the 8 mm screw connecting the wire to the antenna.

    コメントを追加する

    • If desired, the antenna can now be removed by pulling inwards and horizontal to the panel bottom.

    コメントを追加する

    • Use the Phillips #1 screwdriver to remove the four 12 mm screws.

    • Remove the five 6 mm screws at the top with the same screwdriver.

    コメントを追加する

    • Use a Phillips #1 screwdriver and remove the two vertical 8 mm screws from the top.

    コメントを追加する

    • Pry open the inner back panel by inserting the plastic opening tool in the crack at the top corner.

    • Use moderate force to pry it open and take the cover off.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

Michael Johnson

メンバー登録日: 2014年01月31日

237 ポイント

2のガイドは作成済み

チーム

Cal Poly, Team 2-9, Amido Winter 2014 Cal Poly, Team 2-9, Amido Winter 2014人のメンバー

CPSU-AMIDO-W14S2G9

5 メンバー

6のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 0

今までの合計 474