修理を始めるには コミュニティ ストア

Mad Catz Street Fighter IV FightPad Directional Pad Replacement

はじめに

Use this as a guide to remove or replace the rubber part of the directional pad.

必要な工具と部品

  1. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, Rear and Side Case: 手順 1、 1の画像 1

    • Use tweezers to completely remove the sticker from the rear of controller.

    翻訳

  2. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 2、 1の画像 1

    • Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

    翻訳

  3. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 3、 2の画像 1 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 3、 2の画像 2

    • Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.

    • Use the plastic opening tool to pry the two cases apart.

    翻訳

  5. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 4、 2の画像 1 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 4、 2の画像 2

    • Remove the two rubber side grips.

    翻訳

  6. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, RS-DP-LS Switch: 手順 5、 2の画像 1 Mad Catz Street Fighter IV FightPad Directional Pad Replacement, RS-DP-LS Switch: 手順 5、 2の画像 2

    • Locate RS-DP-LS switch.

    • Pull upwards on the switch to remove it.

    翻訳

  7. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, Circuit Board: 手順 6、 1の画像 1

    • Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

    翻訳

  8. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 7、 3の画像 1 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 7、 3の画像 2 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 7、 3の画像 3

    • Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.

    • Be careful with the wires connected to the circuit board itself as they are thin and delicate.

    • When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

    翻訳

  9. Mad Catz Street Fighter IV FightPad Directional Pad Replacement, Directional Pad: 手順 8、 1の画像 1

    • Use tweezers to remove the rubber part of the directional pad.

    翻訳

  10. Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 9、 2の画像 1 Mad Catz Street Fighter IV FightPad Directional Pad Replacement: 手順 9、 2の画像 2

    • Insert a new directional pad over the original directional pad's location.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

6人の作成者と共同で作成されました。

Jefferson

メンバー登録日: 09/26/12

78 ポイント

1ガイドが承認済み

バッジ: 7

+4 個以上のバッジ

チーム

Cal Poly, Team 1-7, Propen Fall 2012 Cal Poly, Team 1-7, Propen Fall 2012人のメンバー

CPSU-PROPEN-F12S1G7

4 メンバー

14のガイドは作成済み

2 件のコメント

mi spiegate l'utilita di questa guida?vendere forse le pinzette e tutte le altre stronzatine che servono per riparare il fightpad?quando invece il pezzo più importante cioè il gommino non lo vendete....fate pena

auredo1988 - 返信

Hi I don't speak Italian but I think you are asking "what is the purpose of this guide?". We made these as a project for university because I wanted to resolder a wire in this controller that came undone. For good measure we made a guide for each individual part although the real purpose of these guides was for the full disassembly and re soldering.

Eric Devlin - 返信

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 3

過去 30 日: 9

今までの合計 4,431