修理を始めるには コミュニティ ストア

MacBook Pro Retina 2012–2015 Feet Replacement

必要条件のみ
この修理ガイドは、他のガイドの前提条件として使用されます。それ自体は不完全で、単独で使用されることはありません。

はじめに

This is a prerequisite guide describing how to replace MacBook Pro Retina feet, applicable to models A1425, A1502, and A1398. For a full guide including lower case removal, refer to the specific MacBook Pro device pages.

必要な工具と部品

  1. MacBook Pro Retina 2012–2015 Feet Replacement, Feet: 手順 1、 2の画像 1 MacBook Pro Retina 2012–2015 Feet Replacement, Feet: 手順 1、 2の画像 2

    • Peel away any stickers from the backside of the rear case covering the feet you have chosen to replace.

    • Any stickers you remove will most likely be unsalvageable for re-use. That's okay! Your MacBook does not need them to function.

    翻訳

  2. MacBook Pro Retina 2012–2015 Feet Replacement: 手順 2、 2の画像 1 MacBook Pro Retina 2012–2015 Feet Replacement: 手順 2、 2の画像 2

    • Remove any broken or damaged feet.

    • If the foot you are replacing is still intact, you can use your tweezers push it out from the inside.

    • If the old foot is difficult to remove, use a hair dryer or a heat gun to apply some heat to the area and loosen the adhesive.

    翻訳

  3. MacBook Pro Retina 2012–2015 Feet Replacement: 手順 3、 1の画像 1

    • Scrub the foot cavity with adhesive remover to remove any remaining adhesive.

    翻訳

  5. MacBook Pro Retina 2012–2015 Feet Replacement: 手順 4、 1の画像 1

    • Wipe the foot cavity with an isopropyl alcohol prep pad to remove any cleaner residue and prep the area for the adhesive on the new foot.

    翻訳

  6. MacBook Pro Retina 2012–2015 Feet Replacement: 手順 5、 1の画像 1

    • Peel a replacement foot from the plastic backing.

    • The adhesive is fairly strong—make sure that you are peeling the foot up, not tearing the plastic backing.

    翻訳

  7. MacBook Pro Retina 2012–2015 Feet Replacement: 手順 6、 3の画像 1 MacBook Pro Retina 2012–2015 Feet Replacement: 手順 6、 3の画像 2 MacBook Pro Retina 2012–2015 Feet Replacement: 手順 6、 3の画像 3

    • Align the new foot inside the cavity.

    • Make sure the alignment nub on the foot is lined up with the small hole near the perimeter of the pad.

    • Lay the foot down while keeping it properly aligned.

    • Check for proper alignment from the inside of the case. The alignment nub should be slightly visible through the alignment hole.

    翻訳

  8. MacBook Pro Retina 2012–2015 Feet Replacement: 手順 7、 2の画像 1 MacBook Pro Retina 2012–2015 Feet Replacement: 手順 7、 2の画像 2

    • Press the new foot into place firmly with your finger, then apply pressure by pinching the foot from either side of the case with your finger and your thumb.

    • Maintain pressure for 30 seconds to set the pressure-sensitive adhesive.

    • Repeat the last seven steps for any remaining broken or worn feet.

    翻訳
終わりに

To reassemble your device, follow these instructions in reverse order.

3 の人々がこのガイドを完成させました。

作成者

3人の作成者と共同で作成されました。

Taylor Dixon

メンバー登録日: 06/26/18

67,033 ポイント

94のガイドは作成済み

バッジ: 40

+37 個以上のバッジ

0 件のコメント

コメントを追加

統計データ:

過去 24時間: 0

過去 7 日: 0

過去 30 日: 4

今までの合計 2,118