はじめに

MacBook Pro Unibodyのバッテリーの交換はとても簡単な作業です。

  1. ケースを閉じた状態で、平らな作業台の上にUnibodyの上部を下側に向けて配置します。
    • ケースを閉じた状態で、平らな作業台の上にUnibodyの上部を下側に向けて配置します。

    • アクセスドアの取り外しラッチの溝のある側を押して、飛び出した側の先端を掴んでください。取り出しラッチを垂直になるまで持ち上げます。

    The A1286 has no Access Door.!!

    I actually can see no sign of the battery!...

    aguib - 返信

    Citaat van aguib:

    The A1286 has no Access Door.!!

    I actually can see no sign of the battery!...

    I assume you have the newer model, with the built-in battery. It's still removable with tools, but these are the wrong instructions for that model.

    lgc90 - 返信

    when will there be a guide for the other unibody macbook pro. that does not have an access door?

    irishking - 返信

    Is there a manual to show, how disasembly the display, i mean, after step 5, to check the display between lcd and aluminiun back case?

    Max

    Max - 返信

    On other guides you state the height of the HD that can be supported, e.g. MacBook Pro 15" Core 2 Duo Model A1211 Hard Drive Replacement , I have read ( but have not confirmed ) that the uni-body MacBook Pro can be fitted with the 750GB and 1TB 12mm drive from Western Digital.

    Can you confirm this?

    Many thanks in advance.

    ahothabeth - 返信

    Citaat van SHerwood Ball:

    My display and aluminum casing has separated.

    I don't know if it just snaps back together or does it need to be glued.

    I dropped mine on the carpeted stairs and the display still works.

    I'm hoping I can just snap it back together and that no plastic pieces or teeth of the snapping

    portion have been broken........

    SHerwood Ball - 返信

    When you say "left fan" is this "left when looking at the logic board after turning the computer over and looking it up opening it up" or "left when sitting at the computer keyboard and typing on it"?

    thvv - 返信

    We always use left and right in reference to the computer when you're using it.

    Andrew Optimus Goldberg -

    Directions were great and the worn dc in board was replaced. The hardest part of the procedure is disconnecting the data display cable. A better description of step 21 is to slide the connector parallel to the circuit board towards the outside corner. Reconnecting correctly took several tries.

    I used the tip of the spudger to nudge the corners a little at a time to seat the connector.

    The ribbon connector for the keyboard has to be inserted all the way before seating the retaining cap. It took me three tries . First try power button did not work second try numbers keys did not work.

    Thanks for the directions ...could not have done it with out them!!!

    landryd - 返信

    Hola. Poseo un MacBook Pro Late 2008 y debo cambiarle las cornetas. Me sirve unas cornetas de un MBP Late 2011?

    jegonzalez80 - 返信

  2. Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
    Fixmasのスピリットを広めましょう
    クーポンコードFIXMAS12を使えば、50ドル以上のお買い上げで12ドル割引となります。
  3. アクセスドアがUnibodyから十分の高さまで持ち上がるはずです。
    • アクセスドアがUnibodyから十分の高さまで持ち上がるはずです。

    コメントを追加する

    • 次の手順に進む前に、アクセスドアの取り外しラッチが垂直になっているか確認してください。

    • 半透明のプラスチックタブを掴んで、バッテリーをUnibodyから引き上げます。

    • ラッチが押されると、バッテリーが所定の位置にロックされます。

    Do I need to wait for the battery to charge completely before using the computer (while plugged in)?

    Kaila Potts - 返信

    No. You do not need to charge it completely before removing it.

    Titus (#1579) - 返信

まとめ

デバイスを再組み立てする際は、これらのインストラクションを逆の順番に従って作業を進めてください。

75 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

83%

Midori Doiさんは世界中で修理する私たちを助けてくれています! 貢献してみませんか?
翻訳を始める ›

Walter Galan

572,715 ポイント

1,203のガイドは作成済み

I recently replaced my battery for the macbook pro late 2008 model number A1281, I have a weared problem with that - System shuts down while connected to power when it is Turned On.

I tried NVRAM reset also but no luck, Any help on this would be appreciable.

Thanks

Kamalarajan

Kamalarajan - 返信

Have just received the A1281 replacement battery. However it does not charge. The magsafe light is on green but the battery is not charging. When I put in my old battery the magsafe goes to amber and it starts to charge. Any ideas?

domburton - 返信

I just bought a new battery to replace A1281, and I have the same issue as you : the battery is not charging, power charger light is green.

I've tried to reset SMC, but it didn't solve anything.

Rodac -

コメントを追加する

統計データを表示:

過去 24時間: 8

過去 7 日: 46

過去 30 日: 255

今までの合計 72,687