メインコンテンツにスキップ

はじめに

Have your MacBook Pro feet seen better days? Use this guide to give your Mid 2012 MacBook Pro a fresh set of feet.

  1. Remove the following P5 pentalobe screws securing the lower case to the MacBook Pro:
    • Remove the following P5 pentalobe screws securing the lower case to the MacBook Pro:

    • Eight 3.0 mm

    • Two 2.3 mm

  2. Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.
    • Lifting from the edge nearest the clutch cover, lift the lower case off the MacBook Pro.

    • Set the lower case aside.

  3. Peel away any stickers from the backside of the rear case covering the feet you have chosen to replace. Any stickers you remove will most likely be unsalvageable for re-use. That's okay! Your MacBook does not need them to function.
    • Peel away any stickers from the backside of the rear case covering the feet you have chosen to replace.

    • Any stickers you remove will most likely be unsalvageable for re-use. That's okay! Your MacBook does not need them to function.

  4. Remove any broken or damaged feet. If the foot you are replacing is still intact, you can use your tweezers  push it out from the inside.
    • Remove any broken or damaged feet.

    • If the foot you are replacing is still intact, you can use your tweezers push it out from the inside.

    • If the old foot is difficult to remove, use a hair dryer or a heat gun to apply some heat to the area and loosen the adhesive.

  5. Scrub the foot cavity with adhesive remover to remove any remaining adhesive.
    • Scrub the foot cavity with adhesive remover to remove any remaining adhesive.

  6. Wipe the foot cavity with an isopropyl alcohol prep pad to remove any cleaner residue and prep the area for the adhesive on the new foot.
    • Wipe the foot cavity with an isopropyl alcohol prep pad to remove any cleaner residue and prep the area for the adhesive on the new foot.

  7. Peel a replacement foot from the plastic backing.
    • Peel a replacement foot from the plastic backing.

    • The adhesive is fairly strong—make sure that you are peeling the foot up, not tearing the plastic backing.

  8. Align the new foot inside the cavity. Make sure the alignment nub on the foot is lined up with the small hole near the perimeter of the pad. Lay the foot down while keeping it properly aligned.
    • Align the new foot inside the cavity.

    • Make sure the alignment nub on the foot is lined up with the small hole near the perimeter of the pad.

    • Lay the foot down while keeping it properly aligned.

    • Check for proper alignment from the inside of the case. The alignment nub should be slightly visible through the alignment hole.

  9. Press the new foot into place firmly with your finger, then apply pressure by pinching the foot from either side of the case with your finger and your thumb. Maintain pressure for 30 seconds to set the pressure-sensitive adhesive.
    • Press the new foot into place firmly with your finger, then apply pressure by pinching the foot from either side of the case with your finger and your thumb.

    • Maintain pressure for 30 seconds to set the pressure-sensitive adhesive.

    • Repeat the last seven steps for any remaining broken or worn feet.

終わりに

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

Taylor Dixon

メンバー登録日: 2018年06月26日

21,712 ポイント

72のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

107 メンバー

9,568のガイドは作成済み

0 件のコメント

コメントを追加

統計データを表示:

過去 24時間: 4

過去 7 日: 25

過去 30 日: 162

今までの合計 2,257