メインコンテンツにスキップ

修理を始めるには

修理する権利

ストア

はじめに

MacBook Air 13インチ Mid 2011のSSDをアップグレードもしくは交換するには、このガイドを参照してください。このMacBook Airは独自のストレージドライブのコネクタを使用しています。そしてアダプタなしではM.2ドライブと 互換性がありません

この修理を行う前に、できる限り現在使用中のSSDのバックアップをしてください。それから インターネットの回復もしくは create a bootable external drive を確認してください。それからmacOSを新ドライブにインストールする準備が完了します。macOSを新しいドライブにインストールし、データを新しいSSDに移行する準備が整います。

最後に、MacBook AirからオリジナルSSDを交換する前に、macOS 10.13 High Sierra (もしくはそれ以降の macOS)にインストールすることをお勧めします。ほとんどの新SSDには、HighSierraより前のバージョンのmacOSにはない更新されたストレージドライバーが必要です。

  1. 作業を始める前に、MacBookの電源を落として下さい。ディスプレイを閉じ柔らかい表面の上に置いてください。
    • 作業を始める前に、MacBookの電源を落として下さい。ディスプレイを閉じ柔らかい表面の上に置いてください。

    • P5ペンタローブドライバーを使って、下部ケースをはずしてください。ネジは次の長さに分かれます。

    • 9mm ネジー 2本

    • 2.6mm ネジー 8本

    Pulling the fan cable out was terrifying but you actually just pull on the cable itself. No way to get any leverage at the connector to dislodge it. Did come out easily but like I said, scared me!

    allison - 返信

    Draai de schroefjes voorzichtig los en leg ze op een stabiele plek neer en let erop dat de schroefje een verschillende lengte hebben.

    bwgvanderveer - 返信

    I thought I could replace my 256 Gb SSD with 512? regards

    ola m - 返信

    Do you have good Test Point Voltages? It appears there are silver colored Test points on the I/O Board. I am working on a water spill and trying to troubleshoot if both the I/O board and the Logic need replaced.

    andrew - 返信

    It's probably not necessary but may be a little safer to completely discharge the old battery before replacing it.

    Larry Smith - 返信

    tell a model that was not inferior to the speed of the one in the laptop.

    Thank you

    ilyabuhov - 返信

    Do i need to order tools separately to replace the battery i just ordered?

    anne uhlir - 返信

    im looking for a Logic Board for a

    Apple - MacBook Air® - 13.3" Display - Intel Core i5 - 8GB Memory - 128GB Flash Storage (Latest Model) - Silver Model: MQD32LL/A

    Any help is appreciated.

    Jamie Comstock - 返信

    P5 pentalobe screwdrivers are too big! The correct size for these screws are p4 pentalobe. P5 pentalobe was just able, with difficulty, to turn some of the screws. If the screws were at all tight, my p5 was unable to get them out, and started to strip the screws. A p4 screwdriver fit better and removed the screws with ease. (I was using high quality Wiha brand screwdrivers.)

    William Skinner - 返信

    I had same experience (with MacBook Air 13-inch Mid-2012) … had to get P4, which worked swimmingly

    eric -

    Very simple installation. The screwdriver heads were exactly what we’re needed, one head for the outside case screws, the other for the screws holding the battery in place. The computer started right up. Now to see how the battery holds up, but I have a good feeling about this!

    Dennis Eaton - 返信

    My P5 and the T5 worked perfectly with my early 2015 Air 13”! And it is super fast! Thank you iFixit!

    Pennny Beach - 返信

    The supplied kit and instructions worked perfectly!

    Nikolay Andreev - 返信

    Comments that the P5 pentalobe are too large are absolutely spot-on. There is no way the P5 pentalobe bit I have will work with the MacBook Air without destroying the screws. Hard target search for P4 pentalobe bit in progress…..

    joemoog - 返信

    Bonjour j’aimerais changer mon SSD de 128 Go pour en mettre un de 512 Go. Je ne sais pas ce qu’il faut prendre car il faut qu’il soit compatible avec le macbook air A1466. J’aurais vu un Samsung Evo 970 500 Go mais si je ne me trompe pas, il faut un adaptateur.

    Merci pour votre aide.

    chicco33 - 返信

    oui, vous aurez besoin d’un adaptateur, pour completez le changement.

    Dan -

    The tool kit should include tweezers for re-inserting the battery connector.

    Andre Clement - 返信

    P5 pentalobe worked perfectly for me. Instructions were spot-on. Antenna connections were a bit fiddly to refit but got them in ok.

    michaelquinnell - 返信

    Maybe the problem some are experiencing is that the designations are confusing (blame Apple rather than iFixit). the P2 is also known as PL1. The P5 is also known as PL4. The P6 is also known as PL5. So it is possible to mistake the P6 (PL5) for the P5 (PL4), meaning it (P6-PL5) will be too big, while the P5 (PL4) will be just right. Sort of a 3 Bears explanation, but it is very confusing.

    Thomas Lewis - 返信

    To add to this. In searching for the P5 screwdriver to buy in UK, as far as I can tell, it is also known as

    Pentalobe 1.2(mm)

    also

    P4 = 0.8

    P6 = 1.5

    Just unscrewed the back case of MacBook Air 13” mid 2011, with no problems using Pentalobe 1.2

    nijafe -

    I have not replaced a display on the A1369 but have done many A1466 which is a newer 13” model. They seem really similar and its not clear why one needs to remove the logic board to remove the display. The antenna cables on the A1466 dont have to rest under the logic board but can be tucked in the hinge crevice. Cant this same thing be done with the A1369?

    Sean Love - 返信

    Did mine today - but new battery wasnt charging. Went back in and noticed the battery connector cable was not quite 100% “seated. It was sticking out by less than a millimetre! - you need to give it quite a firm push in to get it seated properly. Otherwise - all ok .

    John Brennand - 返信

    Just installed on a MacBookAir6,2 (13-inch, Early 2014).

    Was very easy.

    New iFixit battery looks great so far:

    Full Charge Capacity (mAh): 4922 -> 7333

    Jonathan Cross - 返信

    can you tell me which size of screwdrivers you’ve used to crack it up, please? I have the same model and size,

    hawk_lpc -

    Screw P5 Pentalobe 1.2

    Mario Verlent - 返信

    Install went flawlessly. Only challange was reattaching blue tooth antennas. Those sockets are so tiny.

    Joel Sebastian - 返信

    Installation was a little challenging at first because the instructions on this site did not perfectly match my model (late 2013 to early 2015).

    Found this video on YouTube which described the procedure perfectly https://www.youtube.com/watch?v=Lue6lVWh...

    Also the Ifixit kit I received was well put together with everything I needed and more. The calibration went perfectly and I am very pleased. Will buy again!!

    Donald Niamath - 返信

    Gently pulled out connector of old battery, then pressed and held the power switch for 1 minute. Unscrewed and removed the old battery. Pressed and held power switch for 1 minute again. I know from previous work that this helps drain charge from spontaneous recharging as the dielectric recovers. Gently “fine tuned” leads from new battery to connector till connector stuck out at right angle to the edge of battery. Held the battery by the edges and let the connector slide into the socket. Set the battery down and put the screws in all the way. Then checked that the connector was completely seated before tightening the screws. The laptop come on immediately and showed 98% charge and registered normal (checked in “About this Mac”. Very happy to this point. Now for calibration.

    Amir Zaidi - 返信

    Thank you very much for the guilde. My MBA2011 had reborn !

    Billy Wong - 返信

    Allow for electrostatics, otherwise you may cook components on the logicboard /motherboard (like I did with one of these!)

    See great advice: Electrostatic Discharge

    Fletcher Cole - 返信

    … und wenn du eines von diesen wirklich kleinen Schräubchen vermisst: bevor du den Boden aufkehrst oder mit einem starken Magneten absuchst, schau mal am seitlichen (magnetischen) Ladekabelanschluss nach … ?

    ... and if you miss one of these really small screws: before you sweep the floor or search it with a strong magnet, take a look at the (magnetic) charging cable connection on the side … ?

    Blatt - 返信

  2. ディスプレイと下部ケースの間に指を入れ、上に引っ張って下部ケースを本体から外します。
    • ディスプレイと下部ケースの間に指を入れ、上に引っ張って下部ケースを本体から外します。

    • 下部ケースを取り外して脇に置きます。

    There is a nub on the inside of the case which is attached to the battery. When you try to pull it open, it appears to be attached to the plastic casing of the battery, which sometimes splits. I gently unhooked the nub from the battery before removing the case fully. This seems to happen if the battery has suffered some drop damage (plastic parts broken around screws and parts of plastic frame split). Just an FYI in case your lower case doesn't pull away easily.

    Jeannie Crowley - 返信

    To add - the slim 1cm tab “nub” is on the centre of the back cover & fits into a hole in the battery frame. I ran my fingers around the whole of the cover to eventually here it click out.

    nijafe -

    When closing this back up make sure that the antenna cable is tucked away neatly

    Gabriel - 返信

    So this is a legit back cover for MacBook Air?

    ASHANTI SMITH - 返信

    What about disconnecting the battery?

    Luke Grimes - 返信

    I bought the part and tools from iFixit and followed the directions. The mechanical part went smoothly - maybe 10 minutes to disassemble/replace/reassemble.

    Getting Catalina (the current MacOS) to install was not working until I used Cmd-Opt-R (as noted in the OWC paper sheet that came in the box) which brought up the proper installer - I believe from a pre-prepared bootable SD card but it’s hard to say. From there the install succeeded taking ~1.5 hours.

    Beware that (a) the install requires a working internet connection for verification and updates, and (b) the system must have been running at least macOs 10.13 (High Sierra) before the install in order to have an EFI BIOS that recognizes the SSD.

    Lance Berc - 返信

    As noted by others, be a bit careful removing the lower case. There is an oblong black plastic locator very near the center of the lower case. Unless you gently pry the bottom cover pretty much straight up, you will break the ends off of the locater.

    BobY - 返信

  3. アクシデントで放電や感電を防ぐために、ロジックボードからバッテリコネクタを外してください。 バッテリコネクタに付いている透明なプラスチック製のプルタブをつかみ、Airの前端に向かって引っ張り、ロジックボードからバッテリの接続を外します。
    • アクシデントで放電や感電を防ぐために、ロジックボードからバッテリコネクタを外してください。

    • バッテリコネクタに付いている透明なプラスチック製のプルタブをつかみ、Airの前端に向かって引っ張り、ロジックボードからバッテリの接続を外します。

    • コネクタをバッテリー側に向けて水平に引っ張ってください。ロジックボード上のソケットにダメージを与えてしまうため、Air本体から上に引っぱらないでください。

    The clear plastic tab is missing on mine. Whoever worked on my laptop before me seems to have ripped it off. Now what?

    mjmorawski - 返信

    My plastic tab pulled off the connector. I worked the connection apart using two spurgers, slowly backing it out side to side.

    Ric Thistlethwaite - 返信

    I don’t see my socket on logic board, how can I fix it

    QUYNH PHAM - 返信

  4. SSDを基盤に固定している1つの2.9 mm T5トルクスネジを取り外します。
    • SSDを基盤に固定している1つの2.9 mm T5トルクスネジを取り外します。

    Should this screw be really difficult to remove?

    Kitty - 返信

    It should give a little resistance but not a lot that it doesn’t come out.

    Jonathan - 返信

  5. ソケットの損傷を避けるため、SSDを過剰に持ち上げないで下さい。 SSDの端を少し持ち上げまっすぐ引いて基盤上のソケットからから取り外します。
    • ソケットの損傷を避けるため、SSDを過剰に持ち上げないで下さい。

    • SSDの端を少し持ち上げまっすぐ引いて基盤上のソケットからから取り外します。

    • SSDを再び取り付ける際、固定ネジを取り付ける前にSSDが正しく取り付けられているか確認してください。

    I’ve heard tales of an adapter that will make this computer work with a stand SSD drive.

    Doesn’t seem like there’s enough space to make it work, but if this is possible I’d love to learn more.

    Alberto Einsteino - 返信

    Yes, you can put a normal SATA SSD in, with an adapter. I just installed a WD Blue 1TB. This page explains all the details: https://macandegg.com/upkeep/macbook-air...

    peternorthup - 返信

ゴール

78 の人々がこのガイドを完成させました。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

これらの翻訳者の方々は世界を修理する私たちのサポートをしてくれています。 あなたも貢献してみませんか?
翻訳を始める ›

Andrew Bookholt

556,352 ポイント

618のガイドは作成済み

7 件のコメント

If I replace the SSD with another one purchased from iFixit, will it appear as an external or internal drive?

At my job, it's standard to encrypt drives. I purchased an SSD from another vendor and because it showed as external, couldn't be encrypted. I just want to avoid this problem before purchasing one from here.

flux1968 - 返信

Muito bom o roteiro, deu certinho.

ahdesiqueira - 返信

This should really be rated as easy. Took less than 5 minutes thanks to this excellent guide.

Tyler Berry - 返信

Absolutely spot on. Thanks Andrew! The only potential pitfall in this job is getting the right replacement SSD (or, if you're extracting the SSD to use elsewhere, getting the right caddy.)

Ben Godwin - 返信

anybody knows if exist any hdd to replace the ssd?

I have a mb air 13 mid 2011 in my hands and it has behaviour a mac(/pc) with a hdd damaged? same noise, same latencies, same way to damage files…

and over the top “informations about this mac” says it is a macbook pro 13

never seen in my life…

smoker_man2004 - 返信

This was really easy! I removed the hard drive from my mid 2011 MacBook Air and placed it in a free standing caddy - no problem. But it appears that the disk is empty. Is that what it would look like if the hard drive was ruined? (I was told the hard drive was fine - it was my logic board that was fried. So I’m trying to retrieve my data.) Or do I have it inserted wrong? Or… any other explanation?

Tammie - 返信

The one screw holding the SSD will not turn. How much force does it typically take?

Kitty - 返信

コメントを追加

統計データを表示:

過去 24時間: 10

過去 7 日: 137

過去 30 日: 575

今までの合計 160,943