はじめに

Use this guide to replace the AirPort/Bluetooth board.

    • Shut down and close your computer. Lay it on a soft surface top-side down.

    • Remove the following ten screws:

      • Two 8 mm 5-point Pentalobe screws

      • Eight 2.5 mm 5-point Pentalobe screws

    • The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

    When you say:

    Remove the following ten screws:

    Two 8 mm 5-point Pentalobe screws

    Eight 2.5 mm 5-point Pentalobe screws

    Do the 8mm & 2.5mm dimensions refer to the LENGTH of those screws, or the size of the pentalobe? That is, are there other sizes of pentalobe drivers like there are for hex, phillips and torx? When only one dimension is provided, it is usually the socket/driver size, not the screw length, maybe since the length cannot be seen when the screw is installed.

    Can I suggest that you clarify your instructions so folks are confident they are only in need of _one_ pentalobe driver?

    Nerdily yours,

    Larry (whose iPhone 4S can now get through a day without 6 recharges thanks to ifixit.com ;-)

    larryleveen - 返信

    The 8mm and 2.5mm are the length of the screws. One pentalobe P5 screwdriver suffices for all the screws (P5 is implicitly the size of the pentalobe screw heads).

    Michael Welham -

    I sourced all the parts from ifixit, plus a magnetic project mat which I found to be very useful for organising the teardown and reassembly.

    Allen - 返信

    The magnetic mat is

    GERARD SZAREK -

    Keep the 2.5mm tiny screws away from the MagSafe connector as they will be attracted and sucked in to the magnet.

    Frank O'Carroll - 返信

  1. Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
    • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

    コメントを追加する

  2. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • In this step you will disconnect the battery to help avoid shorting out any components during service.

    • Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

    • Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

    When reassembling the connector wire needs to be bent to fit.

    GERARD SZAREK - 返信

    • Use the flat end of a spudger to pry both antenna connectors up from their sockets on the AirPort/Bluetooth card, and move them out of the way of the card.

    コメントを追加する

    • Remove the single 2.9 mm T5 Torx screw securing the AirPort/Bluetooth card to the logic board.

    コメントを追加する

    • Slightly lift the free end of the AirPort/Bluetooth board and pull it straight out of its socket on the logic board.

    • To avoid damaging the socket on the logic board, do not excessively lift the free end of the AirPort/Bluetooth card.

    コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

7 の人々がこのガイドを完成させました。

Sam Lionheart

メンバー登録日: 2012年10月18日

345,096 ポイント

535のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

113 メンバー

7,289のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 12

過去 30 日: 41

今までの合計 3,825