はじめに

Use this guide to replace a damaged heat sink or to reapply its thermal paste.

Be sure to apply a new layer of thermal paste before reinstalling your heat sink.

  • Shut down and close your computer. Lay it on a soft surface top-side down.

  • Remove the following ten screws:

    • Two 8 mm 5-point Pentalobe screws

    • Eight 2.5 mm 5-point Pentalobe screws

  • The special screwdriver needed to remove the 5-point Pentalobe screws can be found here.

When you say:

Remove the following ten screws:

Two 8 mm 5-point Pentalobe screws

Eight 2.5 mm 5-point Pentalobe screws

Do the 8mm & 2.5mm dimensions refer to the LENGTH of those screws, or the size of the pentalobe? That is, are there other sizes of pentalobe drivers like there are for hex, phillips and torx? When only one dimension is provided, it is usually the socket/driver size, not the screw length, maybe since the length cannot be seen when the screw is installed.

Can I suggest that you clarify your instructions so folks are confident they are only in need of _one_ pentalobe driver?

Nerdily yours,

Larry (whose iPhone 4S can now get through a day without 6 recharges thanks to ifixit.com ;-)

larryleveen - 返信

The 8mm and 2.5mm are the length of the screws. One pentalobe P5 screwdriver suffices for all the screws (P5 is implicitly the size of the pentalobe screw heads).

Michael Welham -

I sourced all the parts from ifixit, plus a magnetic project mat which I found to be very useful for organising the teardown and reassembly.

Allen - 返信

Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.
  • Wedge your fingers between the display and the lower case and pull upward to pop the lower case off the Air.

コメントを追加する

In this step you will disconnect the battery to help avoid shorting out any components during service. Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.
  • In this step you will disconnect the battery to help avoid shorting out any components during service.

  • Use the flat end of a spudger to pry both short sides of the battery connector upward to disconnect it from its socket on the logic board.

  • Bend the battery cable slightly away from the logic board so the connector will not accidentally bend back and make contact with its socket.

コメントを追加する

Use the tip of a spudger to carefully push on each side of the iSight camera cable connector to loosen it out of its socket on the logic board. We recommend you gently "walk" the connector out of its socket.
  • Use the tip of a spudger to carefully push on each side of the iSight camera cable connector to loosen it out of its socket on the logic board.

  • We recommend you gently "walk" the connector out of its socket.

コメントを追加する

Peel the iSight camera cable up off the adhesive securing it to the fan. Peel the iSight camera cable up off the adhesive securing it to the fan.
  • Peel the iSight camera cable up off the adhesive securing it to the fan.

コメントを追加する

Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket. Be sure you are prying up on the hinged retaining flap, not the socket itself.
  • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

  • Be sure you are prying up on the hinged retaining flap, not the socket itself.

コメントを追加する

Remove the following three screws securing the fan to the upper case:
  • Remove the following three screws securing the fan to the upper case:

    • Two 5.5 mm T5 Torx screws

    • One 4.6 mm T5 Torx screw

      • In some models this is a 3.6 mm T5 Torx screw.

コメントを追加する

Lift, but do not remove the fan out of its recess in the upper case. Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air. Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air.
  • Lift, but do not remove the fan out of its recess in the upper case.

  • Carefully pull the fan ribbon cable out of its socket as you remove the fan from the Air.

コメントを追加する

Remove the four 2.5 mm T5 Torx screws securing the heat sink to the logic board.
  • Remove the four 2.5 mm T5 Torx screws securing the heat sink to the logic board.

コメントを追加する

  • If the heat sink seems to be stuck to the logic board after removing all four screws, use a spudger to carefully separate the heat sink from the face of the CPU.

  • Remove the heat sink from the logic board.

  • When reinstalling the heat sink, be sure to apply a new layer of thermal paste. If you have never applied thermal paste before, we have a guide that makes it easy.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

ある他の人がこのガイドを完成しました。

Sam Lionheart

メンバー登録日: 2012年10月18日

314,304 ポイント

1,633のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

117 メンバー

5,755のガイドは作成済み

コメント1件

you should seriously note the danger of the cpu screw holders. apple for some reason decided to attach the fricken screw receivers/standoffs via surface mount. they dont have a bottom cap either. use a screw slightly too long or turn too far and pop(screw pushes against motherboard and pops the holder off)... one corner is unable to be screwed in. ask me how i learned this...lol...I cant see how this design decision helps anything but apples wallet. the other side of the board has components smds as well so its not like a really short through hole was undo-able.

John W - 返信

コメントを追加する

統計データを表示:

過去 24時間: 1

過去 7 日: 17

過去 30 日: 25

今までの合計 1,894