はじめに

The interconnect board hosts connections to the logic board, IO board, and both GPUs. Use this guide to remove and replace the interconnect board.

Slide the lock switch to the right, to the unlocked position.
  • Slide the lock switch to the right, to the unlocked position.

コメントを追加する

Lift the outer case straight up off the Mac Pro.
  • Lift the outer case straight up off the Mac Pro.

  • It may help to push down on the center of the fan while lifting the case up.

コメントを追加する

  • Remove five 5.1 mm T10 Torx screws from around the outer perimeter of the fan assembly.

You don't have to remove the fan assy to get to the wifi board & card. It can be done with the fan assy still attached.

Fat Mango - 返信

Fat Mango is correct. That said. If you do pull the fan assembly note that the screws are all held in with blue Permatex and breaking them free takes a fair amount of effort. Getting a good set of Torx screwdrivers is a must.

Jim WIlson - 返信

  • The fan assembly is attached to the rest of the computer by two cables on the IO board side.

  • Tilt the assembly up away from the IO board.

  • Do not try to remove the fan assembly yet, as it is still attached by two cables.

コメントを追加する

  • While supporting the fan assembly with one hand, loosen the two T7 captive screws in the fan cable bracket.

  • These screws are captive in the Mac Pro. Do not try to remove these screws from your Mac Pro.

On my Mac Pro (assembled mid-2017) these are T8 screws. In fact, there were no T7 screws anywhere in my machine.

mark33 - 返信

  • Use a pair of tweezers to pull the fan cable bracket away from the fan assembly.

コメントを追加する

  • Use the flat end of a spudger to disconnect the fan assembly ribbon cable from the IO board.

コメントを追加する

  • Disconnect the fan assembly antenna cable from the IO board.

  • Remove the fan assembly from the Mac Pro.

You don't have to remove the fan assy to do the steps below. They can be done with the fan assy still attached.

Fat Mango - 返信

  • Flip the Mac Pro upside down, 180 degrees.

  • Remove five 5.1 mm T10 Torx screws from the outer perimeter of the lower case.

コメントを追加する

  • Carefully lift the lower case up and remove it from the Mac Pro.

コメントを追加する

  • Use the flat end of a spudger and a twisting motion to gently separate one side of the graphics card data connection.

コメントを追加する

  • Gently separate the other side as well.

  • Flip the connector up and out of the way of the graphics card.

  • Repeat this procedure on the other graphics card.

コメントを追加する

  • Remove the two 6.0 mm T7 Torx screws securing the interconnect board to the heat sink.

These are actually 6.0mm T8 Torx Screws. 12/07/2016.

Todd - 返信

Ended up being T9 screws for me.

Nathaniel Wilson - 返信

On my Mac Pro (assembled mid-2017) these are T8 screws. In fact, there were no T7 screws anywhere in my machine.

mark33 - 返信

  • Gently walk the interconnect board straight up off the logic board's slot connection.

  • It is recommended to lift one side and then the other.

  • Do not try to remove the interconnect board from the Mac Pro yet, as it is still connected to the IO board.

コメントを追加する

  • Flip the interconnect board up and over, exposing the IO board data cable.

  • Use the same sort of twisting and spreading motion with the flat end of a spudger to separate one side of the IO board data cable.

コメントを追加する

  • Use the flat end of a spudger to separate the other side of the IO board data cable.

  • Bend the cable out of the way and remove the interconnect board from the Mac Pro.

コメントを追加する

まとめ

To reassemble your device, follow these instructions in reverse order.

4 の人々がこのガイドを完成させました。

Andrew Optimus Goldberg

メンバー登録日: 2009年10月17日

384,364 ポイント

412のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

107 メンバー

6,518のガイドは作成済み

コメント1件

Why is it necessary to remove the fan?

johnsburdett - 返信

コメントを追加する

統計データを表示:

過去 24時間: 0

過去 7 日: 11

過去 30 日: 37

今までの合計 1,895