はじめに

Mac mini Late 2014の放熱グリスを交換もしくはヒートシンクを交換します。

Mac miniを再組み立てする前に、サーマルコンパウンドを新たに塗るのを忘れないでください。放熱グリスの塗布方法を参照して、サーマルサーフェスを綺麗に拭き取り、準備をしてから、新しいグリスを装着してください。

このガイドはFusion Drive Mac miniを使って作成されました。このモデルには多くのコネクタやコンポーネントが搭載されています。もしあなたのモデルにハードドライブやSSDコネクタがなくても大丈夫です!

  1. 下面カバーは3つのネジ止めによって固定されています。
    • 下面カバーは3つのネジ止めによって固定されています。

    • ネジ止めの近く(ネジ止めの上ではない)を押し開けてください。

    Read Me First: I purchased an SSD drive directly from Crucial and, of course, it came uninitialized. After going thru the entire tear down, installing the new drive, and rebuilding the mini, it refused to recognize the new drive. So, of course, I had to re-tear it down, remove the new drive, insert it into an external housing and format it using my Macbook. After that the mini recognized the new drive. A word to the wise: format the new drive before installing it.

    tom - 返信

    How were you installing the OS? I am planning on booting into a USB drive with a copy of OS High Sierra on it, and I assume I will be able to format my new Samsung SSD using that?

    Simon - 返信

    On my Samsung EVO 850, mac mini download system automaticly

    Stefan Repac - 返信

    Pre-formatting is not necessary if you make a USB boot installation drive with macOS installer. During boot up, hold down the option key until the mac boot into the USB, formatting can then be done using disk utility running off the USB drive.

    SBR249 - 返信

    I had the exact same experience as tom. I installed a brand new 2TB Samsung 850 EVO and it was not recognized by the Mac Mini. I booted from a portable USB drive with a bootable copy of macOS High Sierra but the 850 EVO SSD I had just installed was not shown as an option. I tore down the Mac Mini again, formatted the 850 EVO, rebuilt the Mac Mini, and booted off the same bootable High Sierra USB drive, and sure enough the 850 EVO was recognized.

    maxim - 返信

    diskutil list

    diskutil erasedisk [filesystem] [drivename] /dev/disk[disk number]

    Paul Rodgers - 返信

  2. プラスチックの開口ツールで下面カバーをMacMini本体より押し上げてください。
    • プラスチックの開口ツールで下面カバーをMacMini本体より押し上げてください。

    I used some wooden toothpicks instead of the opening tool. This worked flawless for me.

    mhomscheidt - 返信

    • 下面カバーを引き上げて取り外してください。

    I taped the "Mac Mini Logic Board Removal Tool" to the flat part of the antenna plate before sealing everything up again. I mean, where else am I supposed to store it without forgetting where it is? I'm pretty sure it won't cause any problems there.

    Richard - 返信

    That’s a brilliant idea, @mrredwood!

    Dan Moore -

    I would suggest you wash the underside of the plastic as mine after 3 years was covered in dust.

    John Errington - 返信

    • アンテナプレートから以下のTR6ネジを取り外してください。

      • 3つの4.1mmネジ

      • 3つの1.9mmネジ

    Had a T7 security screw driver [and didn't want to wait to have the T6 version shipped to me], so I gave it a whirl. I lined up the driver with the screw socket, pressed down a bit to make sure the driver would get enough grip, and slowly [but forcefully] rotated the driver and got these screws out. BE CAUTIOUS not to strip the screws. May not work for everyone.

    KevCoStudios - 返信

    As TR6 screwdrivers were sold out all over Germany and I wanted to exchange the HDD THIS friday, I took a VERY fine dental milling tip (0,8 mm head diameter) for my proxxon and milled away the little dots in the center of the the TR6 screws. After that I could open the case with a regular T6 screwdriver. All went fine, MM is closed again + working like a charm with it's new SSD. NOTE: For this task I used my loupe glasses (3x) ;)

    Martin Gerner - 返信

    On the whole screw thing. I just used a tiny dremel drill bit and drilled out the security pin. I hate those screws. I don't see the point in locking the them with those. they should have left the screws alone.

    That Mac Guy - 返信

    That worked for me, thanks for the trick!

    Arroba -

    I used the T7 very carefully. No problems.

    randywardak - 返信

    I just had success using standard pliers to remove the longer screw posts, and then I used standard needle nose pliers to press down and grip the tiny screws. Please note that this method may/will cause scrapping of the aluminium cover.

    Barrythetech - 返信

    Northern Tools sells a set of 13 Torx Security Keys for $28.99 that has the TR6 size.

    Gary Craig - 返信

    On my 2nd drive replacement (swapping out to an SSD this time). Could not find my logic board removal tool. So I made another one from a metal coat hanger. So, here’s my tip, when you put it all back together: the logic board removal tool fits around that small black circle antenna perfectly and you can replace the large black cover over the top snuggly. No rattles or anything.. So, next time: I’m guaranteed to find my logic board removal tool.

    Andy Milne - 返信

    • アンテナプレートを完全に本体から取り外さないでください。アンテナプレートはまだMac miniとアンテナケーブルで繋がっています。

    • 接続端子が自分の方に向くように置き、アンテナケーブルコネクタに触れるようにアンテナプレートを右側に裏返します。

    コメントを追加する

    • アンテナケーブルから1つの3.4mmT6ネジとワッシャーを取り外します。

      • ネジを取り外すときにワッシャーをなくさないように気をつけてください。

    This is a pain in the arse to get back on. Lock the screw down first when reassembling.

    Jim Allen - 返信

    • ピンセットを使ってエアポートカード上にあるソケットからアンテナケーブルコネクタを上に引き抜きます。

    Is this really necessary? The antenna is no where near the SSD drive....

    mike - 返信

    This was the most tricky part for me when remounting the Mac Mini. With my bad eyes, I’ve spent 10 minutes inserting this tiny round antenna plug in the hole. I’ve decided to put the screw back without tighten it too strongly and then it was easier.

    afajner - 返信

    I have been having wifi issues ever since I changed the drive. I don’t know if this connector is the cause or not.

    Simon - 返信

    I have been having wifi issues ever since I did this upgrade. Don’t know if it’s this connector or not.

    Simon - 返信

    Afajner great rip. Worked great. Thx

    Milton - 返信

    Afajner, your tip worked great. Thanks.

    Milton - 返信

    This is a very fiddly connector. Afajner’s tip is recommended. Make sure the connector is in securely. It will not wiggle or make a ticking sound when pressed when it is seated correctly.

    maxim - 返信

    I had trouble at this point too. My experience: Loosen the screw a bit and than center the antenna plug over the pin. In my case I heard a click when I plugged it in correctly. Don’t forget to tighten the screw afterwards.

    Matthias - 返信

    • 気をつけて電源系統とケースの間からアンテナケーブルを引き抜きます。

    コメントを追加する

    • Mac miniからアンテナプレートを取り外します。

    コメントを追加する

    • ファンの2つの12mmT6ネジを取り外します。

    • 27mmT6キャプティブネジを緩めます。

    That 27mm screw should be very loose, since it attaches the motherboard to the case. When you’re trying to remove the motherboard, if the AC connection side of the board is not moving back easily, you need to make sure this screw is fully backed out from the case.

    There’s no danger in removing it completely.

    marklfarley - 返信

    I suggest removing the 27 mm tool, otherwise Step 23 will not work.

    Arvin Bhatnagar - 返信

    • ファンのコネクタはファンの縁の下に隠されています。これはファンを取り出さなければコネクタを外せません。

      • ファンを完全に取り外すまでコネクタを外さないでください。

    • ファンをロジックボードのネジ穴からまっすぐ引き上げてください。

    • ファンのコネクタに触れられるようになるまでSSDからファンを引き抜きます。

    コメントを追加する

    • スパッジャーの先端を使って、ロジックボードの上にあるソケットからファンコネクタを引き上げて抜きます。

    When I did this the entire socket came off the logic board. What do I do now?

    Tyler - 返信

    • Mac miniからファンを取り外します。

    コメントを追加する

    • SATAケーブルコネクタのブラケットを固定している2.6mmT6ネジを外してください。

    This screw is very short, when I tried to put it back, the beginning of its thread got dusted and now it's impossible to use it to fix the bracket in place. It should be 3.5 mm instead of 2.6. Nevertheless, the SATA connector is firmly attached to the logical board withou screw+bracket and my mac mini is working nicely.

    mario.estolano - 返信

    • SATAケーブルコネクタのブラケットを外してください。

    This procedure works to add a SATA hard drive/SSD to a PCIe SSD-only Mac Mini using iFixit's Mac Mini Dual Drive Kit. The one thing that's missing from the kit is SATA cable connector bracket (and screw). This is not the end of the world: the cable is a snug fit in the logic board socket, so the bracket is only a safety measure.

    Dominic Dunlop - 返信

    • ヘラ状のスパッジャーを用いてSATAケーブルコネクタをロジックボード上のソケットから外してください。

    Last time I did this I got the tool under the socket and it broke off. This caused the power light not to work. I don’t use the IR function so it wasn’t an issue. When putting this connector back on, make sure it seats well as many have has issues with the the power light not working. You will read more of this on the comments at the bottom

    Greg Bouten - 返信

    • 先端の尖ったスパッジャーを用いて赤外線センサーケーブルコネクタを外してください。このとき、その部分をソケットからまっすぐ引き抜いてください。

    Be careful in this step. I am known for my gentle hands and the little cable flew out regardless. Was able to reinsert with no damage but was terrifying!

    Liliana Chavez - 返信

    What if the entire connector came off? Can this be glued again? How can I fix this?? :(

    Cai - 返信

    @caicruzz The socket will have to be re-soldered to the board. It’s not terribly difficult, but requires some specialized equipment and I wouldn’t recommend it as a DIY on any machine you care about, at least not without a lot of practice first. I’d suggest reaching out to a repair shop that handles board-level repairs. Sorry for the frustration! Accidents happen sometimes; fortunately this one is very fixable.

    Jeff Suovanen -

    • これからの3つの手順はMac miniにPCle SSDが装着されている場合のみ行ってください。もしハードドライブのみ装着している場合は次の3つの手順は必要ありません。

    • PCle SSDケーブルのブラケットを固定している2つのT6ネジを外してください。

    Steps 18-20 only apply if you are removing a fusion drive. Otherwise skip to step 21 during removal.

    Stephen Reaser - 返信

    • PCle SSDケーブルブラケットを取り出してください。

    コメントを追加する

    • PCle SSDコネクタをソケットから持ち上げて外します。

    Is the PCIe connector present and usable on the mid-range Mac mini? I don't need the ~$300 fusion drive but would like the comfort of knowing that I can add an extra SSD in the future.

    Michael Johnson - 返信

    No, only present in Mac Minis configured with a fusion drive.

    rasmus - 返信

    Not true. I am looking @ the inside of a mac mini _not_ configured with a fusion drive, and the connector is present.

    Samuel Bostick - 返信

    The PCIe connector is only present if the computer came factory configured with any sort of flash storage (SSD or fusion drive). Otherwise, the cable, the connector, the bracket, and the 2 screws are all missing. The fusion drive is essentially a disk drive plus a small capacity SSD blade which the OS recognizes as a combined drive. Fortunately, if you didn’t have an SSD before, you can easily buy the connector cable part on the internet. The bracket and screws are not necessary.

    SBR249 - 返信

    • ロジックボードを固定している1つの16mmT6ネジを外します。

    コメントを追加する

    • ロジックボードを外すには、Mac miniロジックボード専用の取外しツールには入っている円筒形の棒2本を赤くマークされたホール部分に挿入してください。赤くマークされた部分以外のロジックボード上の穴に差し込んだ場合、破損する可能性があります。

    • Mac miniロジックボード専用取外しツールを赤くマークされた2つの穴に入れます。必ず棒がロジックボードの下のケースに到達するまで入れてください。

    Instead of the removal tool it is also possible to use two metal pins with 2,5mm diameter.

    Yuuki Galaxy - 返信

    A T8 screw driver worked best for me on the 4 hard drive screws.

    rparks89 - 返信

    Yes - You need a T8 there rather than T9.

    amrgardner -

    T9 was a perfect fit for me.

    dloftis -

    T8 screws in my HDD

    aiino - 返信

    You don’t need a tool for this step, just turn the Mac Mini around 180º and push the vent for the fan with your thumbs. The board will push straight out. That’s what I did.

    Daniel De Ciantis - 返信

    Simple thumb-pushing didn’t work for me, so I bought the tool.

    Insert the MMLBRtool. How far? There’s an initial lip you might catch about halfway down, but wiggle beyond the lip to a definite bottoming out, and equal lengths of the tool on each side of the elbows as shown.

    As you lever the logic board per the illustrations, you’ll notice the black bezel begin to separate on one side or the other. Use a prying tool or guitar pick to help separate the bezel from the body on top and bottom, and the logic board will slide out easily with gentle prying.

    On my Mini, the bezel’s retaining clips (best seen in Step 25) were very snug to the body, preventing the thumb-push. Using the pick released them from the body.

    s gardner - 返信

    You definitely don’t need the tool. Just get two screwdrivers small enough to fit in the holes and push them both at the same time. I have about a million tiny torx screwdirvers that came with iphone screen replacement kits. I’m sure you do too.

    Mark2000 - 返信

    • 注意しながら I/Oボードに向けてツールを倒します。ロジックボードと I/Oボードはケースからゆっくりスライドすると外れるように組み立てられています。

    • 取り外しツールがケース縁に当たったらストップします。

    • Mac miniロジックボード専用取外しツールを出します。

    I had some trouble getting mine started here. If your logic board seems stuck, try pushing the removal tool on both sides near the bottom (vs the top like the photos show) with your index fingers, holding the case with your ring and pinky fingers so that your hands are completely free of the back of the computer (the side with the ports). This worked for me. Otherwise, this guide made the process smooth!

    moorejeffery - 返信

    The removal tool fits into sockets below the board, just 'lean' the tool over and the logic board will ease out. When refitting the logic board make sure the tabs around the I/O shield slip inside the shell and press home firmly. If the fixing screw does not thread into it's hole, the board is not fully home.

    Malcolm Norwood - 返信

    This is what worked for me!

    Rick Allen -

    Make sure you do *not* have your thumbs on the black plastic I/O shield while attempting this step!

    Stephen Reaser - 返信

    I was able to push the logic board out, with a little bit of stress and patience, without the specified tool. Rather I used two paper clips, larger than average, and being very gentle to get the initial nudge. I then finished it off using only my fingers, as the paper clips were not strong enough and would have bended. Doable, but probably easier with the tool.

    mt - 返信

    Even with the tool - it takes more force than you think. There are clips on both sides of the board. Be aware of that when putting it back.

    Jim Allen -

    I used 2 mini flathead screwdrivers with the same thickness as the holes with the heads aligned straight up and down. They will fit into little sockets attached to the case below the board. The side with the power cord came out much easier than the side with the headphone jack, so I removed the tools after a small gap was created and pushed semi-hard on the logic board with a broken spudger (a screwdriver would have worked, too) right in the elbow curve shown to the left of the screw in step 14, and the whole thing slid right out.

    unixmonkey1 - 返信

    I saw a video where a guy just used a coat hanger to make his own tool. Good to know in case you've already started taking it apart and haven't already purchased the tool. https://www.youtube.com/watch?v=hgEBPlz4...

    James Almeida - 返信

    The coat hanger trick worked flawlessly for me. Very easy.

    Jochen -

    May be its me, but I had a right issue with this, I then noticed the screw I loosened in step 10 was bending over. I removed the screw completely, logic board came out, and the metal pillar on the underneath of the board where said screw went in was bent. When I put it all back together afterwards after changing the drive, that long screw was bend, on straightening everything up, the pillar snapped off the logic board. Everything tightened up and its booted up fine. It might just me not following the instructions properly though

    steve - 返信

    Same here. The screw has to be backed out further than I thought. This should maybe be clearer.

    marklfarley -

    For me the screw loosened in step 10 came out with the fan. it "should" be a captive screw meaning it doesn't stay in when the fan comes out

    Bill Pennock - 返信

    I had 2 complete sets of allen wrenches, one metric and one standard and found one each that fit the holes perfectly. With those I was able to find the "pry spots" that are on the base of the case very easily and a slight nudge moved the board. really worked EXCELLENTLY

    Bill Pennock - 返信

    My logic board was hung up on the left side with the plastic retainer or the two grounding tabs not giving up the ghost. There is no good picture of this on this procedure. If you go the the heat sink replacement procedure you can see a pretty good bit of it below the presenter’s right thumb in the opening pic and in a larger pic at step 27. Not that the logic board assembly can move much while seated I was able to shift (ever so slightly) the black plastic backside to the right and the board finally unlatched and came out. I was so worried that I was going to over force it and break something, you know, like the logic board. Not sure if I have a solution other than don’t force it. If it seems hard and one side seems to have a screw or other some such locking device stop forcing it and try shifting the logic board to the side opposite were it is catching.

    Eric Jorgensen - 返信

    I had an issue during reassembly where the AC in socket was just offset and would not line up correctly. I inserted the power cord (unplugged from wall) as I did the final push and everything finally lined up right.

    Austin McGuire - 返信

    One thing about sliding the assembly board in, i.e. when you are doing the steps backwards, is that there is squishy pad on left and clip on the righ (when viewing mac mini from bottom) if you carefully observe and then it becomes easy to get the assembly in or out if you think about it.

    Trushar - 返信

    • DC-Inケーブルコネクタをロジックボード上のソケットからまっすぐ抜いてください。

    When reassembling, I made the mistake of pushing the logic board all the way in before trying to reattach the DC-In cable connector. It is much easier to reattach the connector with the logic board pushed in just short of final seating.

    Saqib Qazi - 返信

    Very usefull comment!!!

    Jean-Marie Sengelen -

    very small needle-nose pliers help, when reassembling.

    allanschwartz - 返信

    • 注意しながらロジックボードアセンブリをMac miniから外します。このときケーブルを巻き込まないよう気をつけてください。

    When sliding the logic board assembly back in later, mind the tabs, especially those at each end.

    Richard - 返信

    When sliding the logic board back in, also be careful and make sure the rubber “sock” on the logic board wraps around the AC-in socket on the power supply.

    Anton - 返信

    If you can’t get the logic board assembly back in so that it is flush (as it was before you did your surgery on the machine) then I would pay attention to two things: 1) the “sock.” Make sure it is back in place in the right way. I wish I could tell you which way that is but because there is no picture I had to guess and I can’t remember what my guess was now. 2) the retaining clip in step 26. I was unable to properly seat the logic board back into the machine so that it was flush UNTIL I fooled around with the clip and, I GUESS, put it in properly this time. After I did that I was able to properly push the logic board back into place.

    Christopher Todd - 返信

    • ロジックボードにヒートシンクを固定している次のネジを外します。

      • 8.6 mm T8 トルクスネジー4本

      • 2.9 mm T6トルクスネジー1本

    • T8ヒートシンクネジの下に留められたバネを紛失しないようご注意ください。ネジを外した際に一緒に取れてしまいます。

      • 再組み立て中は、ヒートシンクがCPUに対して均等に平らになっているか確認するため、上記のネジを取り付ける際は均等に締めていきます。

    コメントを追加する

    • ロジックボードからヒートシンクを取り出します。

    • すべてのネジを取り外した後にヒートシンクがロジックボードに詰まって取れない場合は、スパッジャーの先端を差し込んで2つのコンポーネントを分離すると便利です。

    • Mac miniを再組み立てする差は、新しいサーマルペーストを塗布してください。塗布方法ガイドを参照してください。

    コメントを追加する

まとめ

デバイスを再組み立てする際は、これらのインストラクションを逆の順番に従って作業を進めてください。

以下の翻訳者の皆さんにお礼を申し上げます:

100%

Midori Doiさんは世界中で修理する私たちを助けてくれています! 貢献してみませんか?
翻訳を始める ›

Sam Lionheart

メンバー登録日: 2012年10月18日

341,601 ポイント

535のガイドは作成済み

チーム

iFixit iFixit人のメンバー

Community

114 メンバー

7,032のガイドは作成済み

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 24

過去 30 日: 110

今までの合計 3,172