メニュー

あなたの設定

MSI GP60 2PE Leopard Wireless Card Replacement

作成者： Zoey Calcagno (そして 4 人のその他投稿者)
  • コメント: 0
  • お気に入り: 0
  • 完了: 2

難易度

普通

手順

11

所要時間

5 - 10 分

セクション

3

フラグ

1

Featured Student Guide

おすすめの学生による修理ガイド

このガイドは当社の素晴らしい学生たちによって作成中であり、iFixitスタッフによってとりわけ素晴らしいガイドであると注目されています。

はじめに

Is your wireless card not working? Here's a guide to replace it. Make sure you follow each step accordingly and carefully replace the wireless card.

ツール

これらのツールを購入する

パーツ

パーツは指定されていません。

  1. Flip MSI GP60 2PE Leopard, so that the back is facing up.

    • Flip MSI GP60 2PE Leopard, so that the back is facing up.

    編集

  2. Find the unlock tab located on the upper right side of the device, then slide it to the right.

    • Find the unlock tab located on the upper right side of the device, then slide it to the right.

    編集

  3. Slide and hold the release tab on the left side of the battery, so that you can remove the battery. Slide and hold the release tab on the left side of the battery, so that you can remove the battery. Slide and hold the release tab on the left side of the battery, so that you can remove the battery.

    • Slide and hold the release tab on the left side of the battery, so that you can remove the battery.

    編集

  4. While holding the release tab, remove the battery slowly. While holding the release tab, remove the battery slowly. While holding the release tab, remove the battery slowly.

    • While holding the release tab, remove the battery slowly.

    編集

  6. Flip the device over so the back is facing up.

    • Flip the device over so the back is facing up.

    編集

  7. Remove the four 5mm screws from the back of the device using a Phillips #00 screwdriver. There is a screw located under the battery; lift the battery up to access it.

    • Remove the four 5mm screws from the back of the device using a Phillips #00 screwdriver.

    • There is a screw located under the battery; lift the battery up to access it.

    編集

  8. Once all four screws are removed, lift the back off. Once all four screws are removed, lift the back off.

    • Once all four screws are removed, lift the back off.

    編集

  9. Locate the wireless card.

    • Locate the wireless card.

    編集

  10. Using a Phillips #00 screwdriver, remove the one 2 mm screw that is holding the wireless card in place.

    • Using a Phillips #00 screwdriver, remove the one 2 mm screw that is holding the wireless card in place.

    編集

  11. Carefully remove the wireless card.

    • Carefully remove the wireless card.

    • Pay close attention to the two wires attached to wireless card.

    編集

  12. Remove the wires connecting to the wireless card by pinching around the base where they connect, then carefully disconnect them. The wires should come off fairly easily.

    • Remove the wires connecting to the wireless card by pinching around the base where they connect, then carefully disconnect them.

    • The wires should come off fairly easily.

    • Avoid yanking or pulling too hard. This can result in the wires breaking.

    編集
終わりに

To reassemble your device, follow these instructions in reverse order.

2 の人々がこのガイドを完成させました。

作成者

4他の投稿者と一緒に

Zoey Calcagno

メンバー登録日: 2018年10月04日

636 ポイント

5のガイドは作成済み

バッジ: 8

+5 個以上のバッジ

チーム

Linn Benton Community College, Team S1-G4, Karnes Fall 2018 Linn Benton Community College, Team S1-G4, Karnes Fall 2018人のメンバー

LBCC-KARNES-F18S1G4

4 メンバー

6のガイドは作成済み

0 件のコメント

コメントを追加

コメントを追加

統計データを表示:

過去 24時間: 0

過去 7 日: 5

過去 30 日: 16

今までの合計 291