メインコンテンツにスキップ

はじめに

You will learn how to remove and install the resistance spring.

パーツ

パーツは指定されていません。

  1. Hold the mouse so that the bottom is facing up.
    • Hold the mouse so that the bottom is facing up.

    • Locate the #1 screw towards the bottom half of the mouse.

    • Take the 4.76 mm Phillips screwdriver and unscrew the #1 screw.

  2. Place the mouse so that the bottom is resting against a hard surface . Gently lift the top cover of the mouse and remove.
    • Place the mouse so that the bottom is resting against a hard surface .

    • Gently lift the top cover of the mouse and remove.

  3. Locate the scroll wheel on the mouse. Grab the scroll wheel with your thumb and index finger. Gently lift up to remove the scroll wheel from the mouse.
    • Locate the scroll wheel on the mouse.

    • Grab the scroll wheel with your thumb and index finger.

    • Gently lift up to remove the scroll wheel from the mouse.

  4. iPhoneのバッテリーキット

    Only $29.99

    Buy Now

    iPhoneのバッテリーキット

    Only $29.99

    Buy Now
  5. Locate the spring on the scroll wheel. The spring is a small piece of metal wire coiled in the middle. Carefully remove the spring from the wheel scroll.
    • Locate the spring on the scroll wheel. The spring is a small piece of metal wire coiled in the middle.

    • Carefully remove the spring from the wheel scroll.

  6. Replace the spring, place it on the correct side of the wheel with the prongs pointing down. The correct side is the side without the black plastic square, as shown in the photos.
    • Replace the spring, place it on the correct side of the wheel with the prongs pointing down.

    • The correct side is the side without the black plastic square, as shown in the photos.

  7. Be aware of where the resistance spring is. This spring will easily fall off. Grab the scroll wheel and its mount and gently pull them apart.
    • Be aware of where the resistance spring is.

    • This spring will easily fall off.

    • Grab the scroll wheel and its mount and gently pull them apart.

  8. Grasp the top of the resistance spring. Pull it towards yourself so the bottom slides out of its hole. Grasp the top of the resistance spring. Pull it towards yourself so the bottom slides out of its hole.
    • Grasp the top of the resistance spring. Pull it towards yourself so the bottom slides out of its hole.

  9. To install the resistance spring, place the hooked section of the spring into the corresponding hole on the mount.
    • To install the resistance spring, place the hooked section of the spring into the corresponding hole on the mount.

まとめ

To reassemble your device, follow these instructions in reverse order.

7 の人々がこのガイドを完成させました。

Maximilian Betkowski

メンバー登録日: 2013年01月11日

172 ポイント

4のガイドは作成済み

チーム

Cal Poly, Team 5-14, Forte Winter 2013 Cal Poly, Team 5-14, Forte Winter 2013人のメンバー

CPSU-FORTE-W13S5G14

5 メンバー

7のガイドは作成済み

This mouse was also available from Dell as an OEM device under the model name "M-UVDEL1". Hopefully the Google juice will help folks repair their devices. I know I would have spent far more time than I did if it weren't for the photos on how to put the spring back. Thanks Maximilian!

Bastien Nocera - 返信

The spring installation details were lifesavers. Thank you!

LB

byard - 返信

thank you! could not have done it without your help.

taiyo_yuden_dvd - 返信

コメントを追加する

統計データを表示:

過去 24時間: 2

過去 7 日: 16

過去 30 日: 68

今までの合計 4,905